Research Article | | Peer-Reviewed

Sustainability and Resiliency Investigation of Grouted Coupler Embedded in RC ABC Bridge Pier at Vehicle Impact

Received: 30 December 2023     Accepted: 12 January 2024     Published: 7 March 2024
Views:       Downloads:
Abstract

Increased occurrences of natural and man-made dynamic loading caused by high strain rate dynamic impact load have been recently reported. Different statistical results indicate that vehicular impacts occur more frequently compared to the other dynamic loads. However, existing literature primarily focuses on enhancing survivability and determining damage levels specifically in relation to faster bridge construction methods used as an accelerated bridge construction (ABC). In this context, the present study investigates the dynamic behavior of a commonly used connection type in ABC, namely grouted coupler that connects pre-cast elements like bridge piers and foundations. To execute the research, both the static and dynamic performance of grouted couplers embedded in pier foundation subjected to high strain rate loading incurred by high velocity vehicular impact are examined. A representative non-traditional reinforced concrete (RC) bridge pier is selected for the study with the standardized geometry and selected material properties. The use of splice sleeves as coupler materials and specified cross-sectional hollow cast iron cylinders filled with high strength concrete grout is employed for developing Finite Element (FE) modeling, extracting data from published journals. A commercial software, ANSYS, has been utilized to develop FE models to capture post impact respective static and dynamic behaviors, and the simulation results are then compared with the analytical. This also includes determining material performance via FE simulations. By considering dynamic loading, the dynamic impact factor (DIF) has been evaluated for the reinforcing steel bar adjacent and embedded into the coupler. In addition, dynamic simulations, and material modulus in demand to sustain impact are determined. Thus, the research necessitates mesh-independent sensitivity studies to investigate DIF corresponding to the precise outcomes. The findings of this study manifests valuable information that aids to opt for the suitable coupler connections, considering material properties, and adequate post impact execution. Consequently, it will serve as a useful design tool for design offices, structural practitioners, and forensic structural engineers.

Published in Engineering and Applied Sciences (Volume 9, Issue 1)
DOI 10.11648/j.eas.20240901.12
Page(s) 14-33
Creative Commons

This is an Open Access article, distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution and reproduction in any medium or format, provided the original work is properly cited.

Copyright

Copyright © The Author(s), 2024. Published by Science Publishing Group

Keywords

Non-Traditional ABC Bridge Pier, High Velocity Vehicle Impact, Grouted Coupler, FEM, and Validation of FE Model

References
[1] (Rusty) Gray, G. T. (2012). “High-Strain-Rate Deformation: Mechanical Behavior and Deformation Substructures Induced.” Annual Review of Materials Research, 42(1), 285–303.
[2] ACI. (2011). ACI 318-11: Building Code Requirements for Structural Concrete. American Concrete Institute.
[3] Actual Speeds on the Roads Compared to the Posted Limits. (2004). https://safety.fhwa.dot.gov/speedmgt/ref_mats/fhwasa09028/resources/actual%20speeds%20on%20roadtopostedlimits.pdf
[4] AFDC. (2018). “Vehicle Weight Classes & Categories.” Alternative Fuels Data Centre, U.S. Department of Energy.
[5] Ameli, M. J., Brown, D. N., Parks, J. E., and Pantelides, C. P. (2016). “Seismic column-to-footing connections using grouted splice sleeves.” ACI Structural Journal, American Concrete Institute, 113(5), 1021–1030.
[6] Ameli, M. J., and Pantelides, C. P. (2017). “Seismic analysis of precast concrete bridge columns connected with grouted splice sleeve connectors.” Journal of Structural Engineering, American Society of Civil Engineers, 143(2), 4016176.
[7] ASTM. (2015). “A706/A706M − 15 Standard Specification for Low-Alloy Steel Deformed and Plain Bars for Concrete.” Astm International, 1–6.
[8] Buth, C. E., Brackin, M. S., Williams, W. F., and Fry, G. T. (2011). “Collision Loads on Bridge Piers : Phase 2. Report of Guidelines for Designing Bridge Piers and Abutments for Vehicle Collisions.” Austin, Texas, 100.
[9] Chopra, A. K. (2001). Dynamics of Structures, Theory and Applications to Earthquake Engineering. Upper Saddle River: Pearson-Prentice Hall.
[10] Cowper, G., and Symonds, P. (1957). “Strain hardening and strain-rate effects in the impact loading of cantilever beam.” Brown University Division of Applied Mathematics, 1–46.
[11] Crosby, D., and Cheremisinoff, N. P. (1988). “Practical Statistics for Engineers and Scientists.” Technometrics, 30(2), 234.
[12] Ebrahimpour, A., Earles, B. E., Maskey, S., Tangarife, M., and Sorensen, A. D. (2016a). Seismic performance of columns with grouted couplers in Idaho accelerated bridge construction applications. Idaho. Transportation Dept.
[13] Ebrahimpour, A., Earles, B. E., Maskey, S., Tangarife, M., and Sorensen, A. D. (2016b). “Seismic performance of columns with grouted couplers in Idaho accelerated bridge construction applications.” (October).
[14] El-Tawil, S., Severino, E., and Fonseca, P. (2005). “Vehicle collision with bridge piers.” Journal of Bridge Engineering, 10(3), 345–353.
[15] Feyerabend, M. (1988). “Hard transverse impacts on steel beams and reinforced concrete beams.” University of Karlsruhe (TH), Germany.
[16] Fhwa. (2018). Concrete Bridge Shear Load Rating Synthesis Report. https://www.fhwa.dot.gov/bridge/loadrating/pubs/hif18061.pdf
[17] For, P., and By, A. (n.d.). GUIDELINES FOR PREPARING UDOT RESEARCH REPORTS.
[18] Furlong, R. W. (2014). “Design for Shear.” 37.
[19] “Grouted Splice Sleeve Connectors for ABC Bridge Joints in High-Seismic Regions – Transportation Blog.” (n.d.). https://blog.udot.utah.gov/2014/09/grouted-splice-sleeve-connectors-for-abc-bridge-joints-in-high-seismic-regions/ (Jul. 13, 2020).
[20] Hauksson, E., Kanamori, H., Stock, J., Cormier, M.-H., and Legg, M. (2014). “Active Pacific North America Plate boundary tectonics as evidenced by seismicity in the oceanic lithosphere offshore Baja California, Mexico.” Geophysical Journal International Geophys. J. Int, 196, 1619–1630.
[21] ICC-ES Evaluation Report ESR-3433. (2014). https://icc-es.org/report-listing/esr-3433/
[22] ICC-ES Report. (2016). https://www.pwcva.gov/assets/2021-05/PA1201Att
[23] Jacob, G. C., Fellers, J. F., Starbuck, J. M., and Simunovic, S. (2004). Crashworthiness of Automotive Composite Material Systems.
[24] Kowalsky, M. J. (2000). “Deformation limit states for circular reinforced concrete bridge columns.” Journal of Structural Engineering, American Society of Civil Engineers, 126(8), 869–878.
[25] Malvar, L. J. (1998). “Review of static and dynamic properties of steel reinforcing bars.” ACI Materials Journal.
[26] Malvar, L. J., and Crawford, J. E. (1998). “Dynamic increase factors for steel reinforcing bars [C].” 28th DDESB Seminar. Orlando, USA.
[27] Pantelides, C. P., Ameli, M. J., Parks, J. E., and Brown, D. N. (2014). Seismic evaluation of grouted splice sleeve connections for precast RC bridge piers in ABC. Utah Department of Transportation.
[28] Roy, S., Unobe, I., and Sorensen, A. D. (2021). “Vehicle-Impact Damage of Reinforced Concrete Bridge Piers: S State-of-the Art Review.” J. Perform. Constr. Facil., American Society of Civil Engineers 2021, 35(5): 03121001, 35(5).
[29] Roy, S., and Sorensen, A. (2021a). “Energy Based Model of Vehicle Impacted Reinforced Bridge Piers Accounting for Concrete Contribution to Resilience.” 18th International Probabilistic Workshop: IPW 2020, Springer Nature, 301.
[30] Roy, S., and Sorensen, A. (2021b). “A Reliability Based Crack Propagation Model for Reinforced Concrete Bridge Piers Subject to Vehicle Impact.” 18th International Probabilistic Workshop: IPW 2020, Springer Nature, 95.
[31] Roy, S., Unobe, I. D., and Sorensen, A. (2022a). “Damage characterization and resilience optimization of reinforced concrete bridge piers under vehicle impact.” Advances in Bridge Engineering, 3(1), 16.
[32] Roy, S., Unobe, I. D., and Sorensen, A. D. (2022b). “Investigation of the performance of grouted couplers in vehicle impacted reinforced concrete ABC bridge piers.” Advances in Bridge Engineering, SpringerOpen, 3(1), 1–30.
[33] Sanders, David H. (2012). “ Evaluation of the Seismic Performance of Circular and Interlocking RC Bridge Columns under Bidirectional Shake Table Loading.” 15th World Conference on Earthquake Engineering (15WCEE), (September 2018).
[34] Sharma, H., Gardoni, P., and Hurlebaus, S. (2015). “Performance-Based probabilistic capacity models and fragility estimates for RC columns subject to vehicle collision.” Computer-Aided Civil and Infrastructure Engineering, 30(7), 555–569.
[35] Sharma, H., Hurlebaus, S., and Gardoni, P. (2012). “Performance-based response evaluation of reinforced concrete columns subject to vehicle impact.” International Journal of Impact Engineering, 43, 52–62.
[36] “Speed limits in the United States - Wikipedia.” (n.d.). https://en.wikipedia.org/wiki/Speed_limits_in_the_United_States (Apr. 24, 2020).
[37] Tavio, T., and Tata, a. (2009). “Predicting Nonlinear Behavior and Stress-Strain Relationship of Rectangular Confined Reinforced Concrete Columns with ANSYS.” Civil Engineering, 11(1), 23–31.
[38] Tazarv, M., and Saiidi, M. S. (2016). “Seismic design of bridge columns incorporating mechanical bar splices in plastic hinge regions.” Engineering Structures, Elsevier, 124, 507–520.
[39] Thomas, R. J., Steel, K., and Sorensen, A. D. (2018). “Reliability analysis of circular reinforced concrete columns subject to sequential vehicular impact and blast loading.” Engineering Structures, Elsevier, 168, 838–851.
[40] Zhao, X., Wu, Y.-F., Leung, A. Y., and Lam, H. F. (2011). “Plastic hinge length in reinforced concrete flexural members.” Procedia Engineering, Elsevier, 14, 1266–1274.
[41] Zhou, D., Li, R., Wang, J., and Guo, C. (2017). “Study on Impact Behavior and Impact Force of Bridge Pier Subjected to Vehicle Collision.” Shock and Vibration, 2017, 1–12.
Cite This Article
  • APA Style

    Roy, S. (2024). Sustainability and Resiliency Investigation of Grouted Coupler Embedded in RC ABC Bridge Pier at Vehicle Impact. Engineering and Applied Sciences, 9(1), 14-33. https://doi.org/10.11648/j.eas.20240901.12

    Copy | Download

    ACS Style

    Roy, S. Sustainability and Resiliency Investigation of Grouted Coupler Embedded in RC ABC Bridge Pier at Vehicle Impact. Eng. Appl. Sci. 2024, 9(1), 14-33. doi: 10.11648/j.eas.20240901.12

    Copy | Download

    AMA Style

    Roy S. Sustainability and Resiliency Investigation of Grouted Coupler Embedded in RC ABC Bridge Pier at Vehicle Impact. Eng Appl Sci. 2024;9(1):14-33. doi: 10.11648/j.eas.20240901.12

    Copy | Download

  • @article{10.11648/j.eas.20240901.12,
      author = {Suman Roy},
      title = {Sustainability and Resiliency Investigation of Grouted Coupler Embedded in RC ABC Bridge Pier at Vehicle Impact},
      journal = {Engineering and Applied Sciences},
      volume = {9},
      number = {1},
      pages = {14-33},
      doi = {10.11648/j.eas.20240901.12},
      url = {https://doi.org/10.11648/j.eas.20240901.12},
      eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.eas.20240901.12},
      abstract = {Increased occurrences of natural and man-made dynamic loading caused by high strain rate dynamic impact load have been recently reported. Different statistical results indicate that vehicular impacts occur more frequently compared to the other dynamic loads. However, existing literature primarily focuses on enhancing survivability and determining damage levels specifically in relation to faster bridge construction methods used as an accelerated bridge construction (ABC). In this context, the present study investigates the dynamic behavior of a commonly used connection type in ABC, namely grouted coupler that connects pre-cast elements like bridge piers and foundations. To execute the research, both the static and dynamic performance of grouted couplers embedded in pier foundation subjected to high strain rate loading incurred by high velocity vehicular impact are examined. A representative non-traditional reinforced concrete (RC) bridge pier is selected for the study with the standardized geometry and selected material properties. The use of splice sleeves as coupler materials and specified cross-sectional hollow cast iron cylinders filled with high strength concrete grout is employed for developing Finite Element (FE) modeling, extracting data from published journals. A commercial software, ANSYS, has been utilized to develop FE models to capture post impact respective static and dynamic behaviors, and the simulation results are then compared with the analytical. This also includes determining material performance via FE simulations. By considering dynamic loading, the dynamic impact factor (DIF) has been evaluated for the reinforcing steel bar adjacent and embedded into the coupler. In addition, dynamic simulations, and material modulus in demand to sustain impact are determined. Thus, the research necessitates mesh-independent sensitivity studies to investigate DIF corresponding to the precise outcomes. The findings of this study manifests valuable information that aids to opt for the suitable coupler connections, considering material properties, and adequate post impact execution. Consequently, it will serve as a useful design tool for design offices, structural practitioners, and forensic structural engineers.
    },
     year = {2024}
    }
    

    Copy | Download

  • TY  - JOUR
    T1  - Sustainability and Resiliency Investigation of Grouted Coupler Embedded in RC ABC Bridge Pier at Vehicle Impact
    AU  - Suman Roy
    Y1  - 2024/03/07
    PY  - 2024
    N1  - https://doi.org/10.11648/j.eas.20240901.12
    DO  - 10.11648/j.eas.20240901.12
    T2  - Engineering and Applied Sciences
    JF  - Engineering and Applied Sciences
    JO  - Engineering and Applied Sciences
    SP  - 14
    EP  - 33
    PB  - Science Publishing Group
    SN  - 2575-1468
    UR  - https://doi.org/10.11648/j.eas.20240901.12
    AB  - Increased occurrences of natural and man-made dynamic loading caused by high strain rate dynamic impact load have been recently reported. Different statistical results indicate that vehicular impacts occur more frequently compared to the other dynamic loads. However, existing literature primarily focuses on enhancing survivability and determining damage levels specifically in relation to faster bridge construction methods used as an accelerated bridge construction (ABC). In this context, the present study investigates the dynamic behavior of a commonly used connection type in ABC, namely grouted coupler that connects pre-cast elements like bridge piers and foundations. To execute the research, both the static and dynamic performance of grouted couplers embedded in pier foundation subjected to high strain rate loading incurred by high velocity vehicular impact are examined. A representative non-traditional reinforced concrete (RC) bridge pier is selected for the study with the standardized geometry and selected material properties. The use of splice sleeves as coupler materials and specified cross-sectional hollow cast iron cylinders filled with high strength concrete grout is employed for developing Finite Element (FE) modeling, extracting data from published journals. A commercial software, ANSYS, has been utilized to develop FE models to capture post impact respective static and dynamic behaviors, and the simulation results are then compared with the analytical. This also includes determining material performance via FE simulations. By considering dynamic loading, the dynamic impact factor (DIF) has been evaluated for the reinforcing steel bar adjacent and embedded into the coupler. In addition, dynamic simulations, and material modulus in demand to sustain impact are determined. Thus, the research necessitates mesh-independent sensitivity studies to investigate DIF corresponding to the precise outcomes. The findings of this study manifests valuable information that aids to opt for the suitable coupler connections, considering material properties, and adequate post impact execution. Consequently, it will serve as a useful design tool for design offices, structural practitioners, and forensic structural engineers.
    
    VL  - 9
    IS  - 1
    ER  - 

    Copy | Download

Author Information
  • Department of Civil and Environmental Engineering, Utah State University, Logan, Utah, U.S.A

  • Sections