| Peer-Reviewed

Investigating the Propagation of the Colloidal Dispersion Gel (CDG) in Thick Heterogeneous Reservoirs Using Numerical Simulation

Received: 17 January 2019     Accepted: 25 February 2019     Published: 16 March 2019
Views:       Downloads:
Abstract

Over the last few decades, there has been a dispute regarding the ability of colloidal dispersion gels (CDG) to improve sweep efficiency more than polymer flooding. In this study, a numerical model was built using the CMG-STARS simulator to investigate the behavior of injecting 0.1 PV of CDG slug into one quarter of inverted nine-spot pattern. This slug was composed of 0.1 wt. % HPAM polymer solution with a polymer-to-crosslinker ratio (P/X) of 50/1. The model was represented by a thick heterogeneous reservoir with high water cut caused by high heterogeneity and adverse mobility ratio. Different experimental results from published literatures have been implemented in the numerical model to study the effect of these parameters on the propagation of the CDG. The results confirmed that CDG could propagate deep into the thief zones and reduce their permeability more than polymer solution. Moreover, the results showed that the shear-thinning behavior of CDG could assist the selective penetration into the high-permeability streaks only, thus reducing the cost of isolating the thief zones by mechanical methods. In addition, the results showed that the wettability had tremendous effects on the treatment. Therefore, the water-wet system yielded higher results with less damage to the low-permeability layers compared to the oil-wet system. The results showed an overestimation of the performance of post-treatment water when considering irreversible adsorption of CDG. However, the prolonged injection of post-treatment water would not remove the permeability reduction caused by CDG flooding, even with reversible adsorption. The results revealed that the higher the degradation of the CDG, the lower the recovery factor. The results showed the importance of considering a combination injection of polymer and CDG. The results also revealed that the higher the salinity of the reservoir brine and/or the makeup water, the lower the recovery factor. In addition, as the polymer/crosslinker ratio increases, the recovery factor decreases, while as the polymer hydrolysis increases, the recovery factor and residual resistance factor increases.

Published in American Journal of Science, Engineering and Technology (Volume 4, Issue 1)
DOI 10.11648/j.ajset.20190401.11
Page(s) 1-17
Creative Commons

This is an Open Access article, distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution and reproduction in any medium or format, provided the original work is properly cited.

Copyright

Copyright © The Author(s), 2019. Published by Science Publishing Group

Keywords

Colloidal Dispersion Gel, Heterogeneous Reservoirs, Numerical Simulation, In-Depth Treatment

References
[1] Sheng, J. J. 2011. Modern Chemical Enhanced Oil Recovery: Theory and Practice. Burlington, MA, USA: Gulf Professional Publishing.
[2] Abdulbaki, M., Huh, C., Sepehrnoori, K., et al. 2014. A Critical Review on use of Polymer Microgels for Conformance Control Purposes. J Petrol Sci & Eng 122: 741-753. https://doi.org/10.1016/j.petrol.2014.06.034.
[3] Ranganathan, R. Lewis, R., McCool, C. S. et al. 1998. Experimental Study of the Gelation Behavior of a Polyacrylamide/Aluminum Citrate Colloidal-Dispersion Gel System. SPE J 03 (04): 337-343. SPE-52503-PA. https://doi.org/10.2118/52503-PA.
[4] Shiyi, Y., Dong, H., Qiang, W. et al. 2000. Numerical Simulation Study on Weak Gel Injection. Presented at the SPE Asia Pacific Oil and Gas Conference Exhibition, Brisbane, Australia, 16-18 October. SPE-64291-MS. https://doi.org/10.2118/64291-MS.
[5] Sydansk, R. D. 1988. A New Conformance-Improvement-Treatment Chromium (III) Gel Technology. Presented at the SPE Enhance Oil Recovery Symposium, Tulsa, Oklahoma, USA, 16-21 April. SPE-17329-MS. https://doi.org/10.2118/17329-MS.
[6] Mack, J. C. and Smith, J. E. 1994. In-Depth Colloidal dispersion Gels Improve Oil Recovery Efficiency. Paper SPE/DOE 27780 Presented at the SPE/DOE Ninth Symposium on IOR, Tulsa, Oklahoma, USA, 17-20 April. SPE-27780-MS. https://doi.org/10.2118/27780-MS.
[7] Smith, J. E., Liu, H., and Guo, Z. D. 2000. Laboratory Studies of In-Depth Colloidal Dispersion Gel Technology for Daqing Oil Field. Presented at the SPE/AAPG Western Regional Meeting, Long Beach, California, USA, 19-22 June. SPE-62610-MS. https://doi.org/10.2118/62610-MS.
[8] Chang, H. L, Sui, X. Xia, L. et al. 2006. Successful Filed Pilot of In-Depth Colloidal Dispersion Gel (CDG) Technology in Daqing Oil Field. SPE Res Eval & Eng 09 (06): 664-673. SPE-89460-PA. https://doi.org/10.2118/89460-PA.
[9] Diaz, D. Saez, N. et al. 2015. CDG in a Heterogeneous Fluvial Reservoir in Argentina: Pilot and Field Expansion Evaluation. Presented at the SPE/EOR Kuala Lumpur, Malaysia, 11-13 August. SPE-174704-MS. https://doi.org/10.2118/174704-MS.
[10] Manrique, E. and Lantz, M. 2011. Colloidal Dispersion Gels (CDG) and their Application in Wyoming and Elsewhere. The 3rd Annual Wyoming IOR/EOR Conference, Jackson Hole, Wyoming, USA.
[11] Muruaga, E., Flores, M. V., Norman, C. et al. 2008. Combining Bulk Gels and Colloidal Dispersion Gels for Improved Volumetric Sweep Efficiency in a Mature Waterflood. Presented at the SPE Symposium on Improved Oil Recovery, Tulsa, Oklahoma, USA, 20-23 April. SPE-113334-MS. https://doi.org/10.2118/113334-MS.
[12] Sandoval, J. R., Manrique, E. J., Perez, H. H. et al. 2010. Dina Cretaceo Field Chemical EOR: From Screening to Pilot Design. Presented at the SPE Latin American and Caribbean Petroleum Engineering Conference, Lima, Peru, 1-3 December. SPE-139200-MS. https://doi.org/10.2118/139200-MS.
[13] Castro, R., Maya, J. et al. 2013a. Colloidal Dispersion Gels (CDG) in Dina Cretaceous Field: From Pilot Design to Field Implementation and Performance. Presented at the SPE Enhanced Oil Recovery Conference, Kuala Lumpur, Malaysia, 2-4 July. SPE-165273-MS. https://doi.org/10.2118/165273-MS.
[14] Castro, R., Maya, G. A., Sandoval, J. E. et al. 2013b. Colloidal Dispersion Gel (CDG) To Improve Volumetric Sweep Efficiency in Water Flooding Processes. CTF Cienc Tecnol Futuro 05 (03): 61-78.
[15] Fielding Jr., R. C., Gibbons, D. H., and Legrand, F. P. 1994. In-Depth Drive Fluid Diversion Using an Evaluation of Colloidal Dispersion Gels and New Bulk Gels: An Operational Case History of North Rainbow Ranch Unit. Presented at the SPE/DOE IOR Symposium, Tulsa, Oklahoma, USA, 17-20 April. SPE-27773-MS. https://doi.org/10.2118/27773-MS.
[16] Manrique, E., Reyes, S., Romero, J. et al. 2014. Colloidal Dispersion Gels (CDG): Field Projects Review. Presented at the SPE EOR Conference at Oil and Gas West Asia, Muscat, the Sultanate of Oman, 31 March-2 April. SPE-169705-MS. https://doi.org/10.2118/169705-MS.
[17] Wang, W. Gu, Y., and Liu, Y. 2003. Applications of Weak Gel for In-Depth Profile Modification and Oil Displacement. J Can Pet Technol 42 (06): 54-61. PETSOC-03-06-04. https://doi.org/10.2118/03-06-04.
[18] Al-Assi, A. A., Willhite G. P., Green, D. W. et al. 2009. Formation and Propagation of Gel Aggregates using Partially Hydrolyzed Polyacrylamide and Aluminum Citrate. SPE J 14 (03): 450-461. SPE-100049-PA. https://doi.org/10.2118/100049-PA.
[19] Seright, R. S. 1994. Propagation of an Aluminum Citrate-HPAM Colloidal Dispersion Gel through Berea Sandstone. In Seright, R. 1995. Improved Techniques for Fluid Diversion in Oil Recovery Processes. Annual Report. Report No. DOE/BC/14880-10. U.S. DOE, Office of Fossil Energy, Washington, D.C., USA, September 1994 and March 1995. 51-64.
[20] Seright, R. S., Han, P., and Wang, D. 2006. Current Colloidal Dispersion Gels are not Superior to Polymer Flooding. Petrol Geol & Oilfield Develop in Daqing 25 (05): 71-80. Article ID: 1000-3754 (2006) 05-0071-10.
[21] Diaz, D., Somaruga, C., Norman, C. et al. 2008. Colloidal Dispersion Gels Improve Recovery in a Heterogeneous Argentina Waterflood. Presented at the SPE Symposium on IOR, Tulsa, Oklahoma, USA, 20-23 April. SPE-113320-MS. https://doi.org/10.2118/113320-MS.
[22] Alvand, E., Aalaie, J., Hemmati, M. et al. 2016. Colloidal dispersion gels based on sulfonated polyacrylamide and chromium triacetate for harsh-environment. Korean J Chem Eng 33 (06): 1654-1963. http://doi.org/10.1007/s11814-016-0025-6.
[23] Helleren, J. 2011. Numerical Simulation of Chemical Flow-Zone Isolation. M.Sc. Thesis, University of Stavanger, Faculty of Science and Technology, Department of Petroleum Engineering. http://hdl.handle.net/11250/183325.
[24] Al-Muntasheri, G. A., Nasr-El-Din, H. A., and Zitha, P. L. J. 2008. Gelation kinetics of an Organically Cross-Linked Gel at High Temperature and Pressure. SPE J 13 (03): 337-345. SPE-104071-PA. http://dx.doi.org/10.2118/104071-PA.
[25] Scott, T., Roberts, L. J., Sharpe, S. R., et al. 1987. In-situ Gel Calculations in Complex Reservoir Systems using a New Chemical Flood Simulator. SPE Res Eng 02 (04): 634-646. SPE-14234-PA. https://doi.org/10.2118/14234-PA.
[26] CMG-STARS User Guide, 2015.
[27] Clifford, P. J. and Sorbie, K. S. 1985. The Effects of Chemical Degradation on Polymer Flooding. Presented at the International Symposium on Oilfield and Geothermal Chemistry, Phoenix, Arizona, USA, 9-11 April. https://doi.org/10.2118/13586-MS.
[28] Chauveteau, G., and Kohler, N. 1974 Polymer Flooding: The Essential Elements for Laboratory Evaluation. Presented at SPE/IOR Symposium, 22-24 April. Tulsa, Oklahoma, SPE-4745-MS. https://doi.org/10.2118/4745-MS.
[29] Seright, R. S. and Martin, F. D. 1993. Impact of Gelation pH, Rock Permeability, and Lithology on the Performance of a Monomer-Based Gel. SPE Res Eng 08 (01): 43-50. SPE-20999-PA. https://dx.doi.org/10.2118/20999-PA.
[30] Jennings, R. R., Rogers, J. H., and West, T. J. 1970. Factors Influencing Mobility Control by Polymer Solutions. JPT 23, (03): 391-401, SPE-2867-PA. https://doi.org/10.2118/2867-PA.
[31] Needham, R. B. and Doe, P. H. 1987. Polymer Flooding Review. J Pet Technol 39 (12): 1503-1507. SPE-17140-PA. https://doi.org/10.2118/17140-PA.
[32] Bai, B., Wang, Q., Du, Y. et al. 2004. Factors Affecting In-Depth Gel Treatment for Reservoirs with Thick Heterogeneous Oil Layers. Presented at the fifth Canadian International Petroleum Conference, Calgary, Alberta, Canada, 8-10 June. PETSOC-2004-140. https://doi.org/10.2118/2004-140.
[33] Carpenter, C. 2016. Colloidal-Dispersion Gel in a Heterogeneous Reservoir in Argentina. J Pet Technol 68 (06): 82-83. SPE-0616-0082-JPT. https://doi.org/10.2118/0616-0082-JPT.
[34] Seright, R. S, Zhang, G., Akanni, O. et al. 2012. A Comparison of Polymer Flooding with In-Depth Profile Modification. J Can Pet Technol 51 (5): 393- 402. SPE-146087-PA. https://doi.org/10.2118/146087-PA.
[35] Zhidong, G., Chang, H. L., Fan, C. et al. 2011. Comparison of Oil Displacement Characteristics between CDG and Polymer Flooding in the Daqing Oilfield. Presented at the SPE Enhanced Oil Recovery Conference, Kuala Lumpur, Malaysia, 19-21 July. SPE-144119-MS. https://doi.org/10.2118/144119-MS.
[36] Seright, R. S. 1988. Placement of Gels to Modify Injection Profiles. Presented at the SPE Enhanced Oil Recovery Symposium, Tulsa, Oklahoma, USA, 16-21 April. SPE-17332-MS. https://doi.org/10.2118/17332-MS.
[37] Seright, R. S. 1991. Effect of Rheology on Gel Placement. SPE Res Eng 06 (02): 212-218. SPE-18502-PA. https://doi.org/10.2118/18502-PA.
[38] Seright, R. S. 1996. Improved Methods for Water Shutoff. PRRC Report 96-23, Semi-Annual Technical Report, Submitted to BDM-OKLAHOMA/The US DOE.
[39] Hoefner, M. L., Seetharam, R. V., Shu, P. et al. 1992. Selective Penetration of Bioploymer profile-Control Gels: Experiment and Model. J of Petrol Sci & Eng 07 (1-2): 53-66. https://doi.org/10.1016/0920-4105(92)90008-O.
[40] Lee, K. S. 2011. Performance of a Polymer Flood with Shear-Thinning Fluid in Heterogeneous Layered Systems with Crossflow. Energies 04 (08): 1112-1128. https://doi.org/10.3390/en4081112.
[41] Green, D. W. and Willhite, G. P. 1998. Enhanced Oil Recovery, Society of Petroleum Engineers, Richardson, Texas, USA.
[42] Wang, D., Seright, R., Zhenbo, S. et al. 2007. Key Aspects of Project Design for Polymer Flooding. Presented at the SPE Annual Technical Conference and Exhibition, Anaheim, California, USA, 11-14 November. SPE-109682-MS. https://doi.org/10.2118/109682-MS.
[43] Manichand, R. N. and Seright, R. 2014. Field vs. Laboratory Polymer-Retention Values for a Polymer Flood in the Tambaredjo Field. SPE Res Eval & Eng 17 (03): 314-325. SPE-169027-PA. https://doi.org/10.2118/169027-PA.
[44] Hoteit, H., Alexis, D., Adepoju, O. O. et al. 2016. Numerical and Experimental Investigation pf polymer-Induced Resistance to Flow in Reservoirs Undergoing a Chemical Flood. Presented at the SPE Annual technical Conference and Exhibition, Dubai, UAE, 26-28 September. SPE-181720-MS. https://doi.org/10.2118/181720-MS.
[45] Asen, S. M., Stavland, A., Strand, D. et al. 2018. An Experimental Investigation of Polymer Mechanical Degradation at cm and m Scale. Presented at the SPE Improved Oil Recovery Conference, Tulsa, Oklahoma, USA, 14-18 April. SPE-190225-MS. https://doi.org/10.2118/190225-MS.
[46] Morris, C. W. and Jackson, K. M. 1978. Mechanical Degradation of Polyacrylamide Solutions in Porous Media. Presented at the SPE Symposium on Improved Oil Recovery, Tulsa, Oklahoma, USA, 16-17 April. SPE-7064-MS. https://doi.org/10.2118/7064-MS.
[47] Sorbie, K. S. 1991. Polymer-Improved Oil Recovery, CRC Press, Boca Raton, Florida, USA (1991).
[48] Sorbie, K. S. and Roberts, L. J. 1984. A Model for Calculating Polymer Injectivity Including the Effects of Shear Degradation. Presented at the SPE Enhance Oil Recovery Symposium, Tulsa, Oklahoma, USA, 15-18 April. SPE-12654-MS. https://doi.org/10.2118/12654-MS.
[49] Zaitoun, A., Makakou, P., Blin, N. et al. 2012. Shear Stability of EOR Polymers. SPE J 17 (02): 335-339. SPE-141113-PA. https://doi.org/10.2118/141113-PA.
[50] Brakstad, K. and Rosenkilde, C. 2016. Modelling Viscosity and Mechanical Degradation of Polyacrylamide Solutions in Porous Media. Presented at the SPE Improved Oil Recovery Conference, Tulsa, Oklahoma, USA, 11-13 April. SPE-179593-MS. https://doi.org/10.2118/179593-MS.
[51] Sheng, J. J. 2015. Status of surfactant EOR technology. J. Petrol 01 (02): 97-105. https://doi.org/10.1016/j.petlm.2015.07.003.
[52] Aldhaheri, M. N., Wei, M., and Bai, B. 2016. Comprehensive Guidelines for the Application of In-Situ Polymer Gels for Injection Well Conformance Improvement Based on Field Projects. Presented at the SPE Improved Oil Recovery Conference, Tulsa, Oklahoma, USA, 11-13 April. SPE-179575-MS. https://doi.org/10.2118/179575-MS.
[53] Abdulbaki, M. R. 2012. Simulation Study of Polymer Microgel Conformance Treatments. Master Thesis. The University of Texas at Austin, Austin, Texas, USA (2012).
[54] Aluhwal, O. 2008. Simulation Study of Improving Oil Recovery by Polymer Flooding in a Malaysian Reservoir. Master Thesis, Universiti Teknologi Malaysia. Kuala Lumpur, Malaysia (2008).
[55] Sedaghat, M. H., Ghazanfari, M. H., Masihi, M. et al. 2013. Experimental and numerical investigation of polymer flooding in fractured heavy oil five-spot systems. J Petrol Sci Eng 108: 370-382. https://doi.org/10.1016/j.petrol.2013.07.001.
[56] Vossoughi, S. 2000. Profile modification using in-situ gelation technology- A review. J Petrol Sci & Eng 26 (1-4): 199-209. https://doi.org/10.1016/S0920-4105(00)00034-6.
[57] Ahmed, T. 2001. Reservoir Engineering Handbook 2nd Edition, Gulf Professional Publishing.
[58] Shen, G. X., Lee J. H., and Lee, K. S. 2013. The Effects of Wettability on Gel Performance in Layered Heterogeneous Reservoirs. Applied Mechanics and Materials 448-453: 4028-4032. http://doi.org/10.4028/www.scientific.net/AMM.448-453.4028.
[59] Shen, G. X., Lee J. H., and Lee, K. S. 2014. Influence of Temperature on Gel Treatment under Various Reservoir Wettability Conditions. Presented at the Offshore Technology Conference Asia. Kuala Lumpur, Malaysia, 25-28 March. OTC-24853-MS. https://doi.org/10.4043/24853-MS.
[60] Tariq K. Khamees and Ralph E. Flori 2018. A comprehensive evaluation of the parameters that affect the performance of in-situ gelation system. Fuel 225: 140-160. https://doi.org/10.1016/j.fuel.2018.03.115.
[61] Tariq K. Khamees, Ralph E. Flori, Ahmed A. Alsubaih et al. 2018. Modeling the Effects of Salinity, Polymer Rheology, Temperature, and Reservoir Wettability on the Performance of In-Depth Gel Treatment Coupled with Surfactant and Polymer Flooding. Presented at the Abu Dhabi Petroleum Exhibition & Conference, Abu Dhabi, UAE, 12-15 November. SPE-193011-MS. https://doi.org/10.2118/193011-MS.
[62] Martin, F. D. and Shrewood, N. S. 1975. The Effect of Hydrolysis of Polyacrylamide on Solution Viscosity, Polymer Retention and Flow Resistance Properties. Presented at the SPE Rocky Mountain Regional Meeting, Denver, Colorado, USA. 7-9 April. SPE-5339-MS. https://doi.org/10.2118/5339-MS.
Cite This Article
  • APA Style

    Tariq Khamees, Ralph Flori. (2019). Investigating the Propagation of the Colloidal Dispersion Gel (CDG) in Thick Heterogeneous Reservoirs Using Numerical Simulation. American Journal of Science, Engineering and Technology, 4(1), 1-17. https://doi.org/10.11648/j.ajset.20190401.11

    Copy | Download

    ACS Style

    Tariq Khamees; Ralph Flori. Investigating the Propagation of the Colloidal Dispersion Gel (CDG) in Thick Heterogeneous Reservoirs Using Numerical Simulation. Am. J. Sci. Eng. Technol. 2019, 4(1), 1-17. doi: 10.11648/j.ajset.20190401.11

    Copy | Download

    AMA Style

    Tariq Khamees, Ralph Flori. Investigating the Propagation of the Colloidal Dispersion Gel (CDG) in Thick Heterogeneous Reservoirs Using Numerical Simulation. Am J Sci Eng Technol. 2019;4(1):1-17. doi: 10.11648/j.ajset.20190401.11

    Copy | Download

  • @article{10.11648/j.ajset.20190401.11,
      author = {Tariq Khamees and Ralph Flori},
      title = {Investigating the Propagation of the Colloidal Dispersion Gel (CDG) in Thick Heterogeneous Reservoirs Using Numerical Simulation},
      journal = {American Journal of Science, Engineering and Technology},
      volume = {4},
      number = {1},
      pages = {1-17},
      doi = {10.11648/j.ajset.20190401.11},
      url = {https://doi.org/10.11648/j.ajset.20190401.11},
      eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.ajset.20190401.11},
      abstract = {Over the last few decades, there has been a dispute regarding the ability of colloidal dispersion gels (CDG) to improve sweep efficiency more than polymer flooding. In this study, a numerical model was built using the CMG-STARS simulator to investigate the behavior of injecting 0.1 PV of CDG slug into one quarter of inverted nine-spot pattern. This slug was composed of 0.1 wt. % HPAM polymer solution with a polymer-to-crosslinker ratio (P/X) of 50/1. The model was represented by a thick heterogeneous reservoir with high water cut caused by high heterogeneity and adverse mobility ratio. Different experimental results from published literatures have been implemented in the numerical model to study the effect of these parameters on the propagation of the CDG. The results confirmed that CDG could propagate deep into the thief zones and reduce their permeability more than polymer solution. Moreover, the results showed that the shear-thinning behavior of CDG could assist the selective penetration into the high-permeability streaks only, thus reducing the cost of isolating the thief zones by mechanical methods. In addition, the results showed that the wettability had tremendous effects on the treatment. Therefore, the water-wet system yielded higher results with less damage to the low-permeability layers compared to the oil-wet system. The results showed an overestimation of the performance of post-treatment water when considering irreversible adsorption of CDG. However, the prolonged injection of post-treatment water would not remove the permeability reduction caused by CDG flooding, even with reversible adsorption. The results revealed that the higher the degradation of the CDG, the lower the recovery factor. The results showed the importance of considering a combination injection of polymer and CDG. The results also revealed that the higher the salinity of the reservoir brine and/or the makeup water, the lower the recovery factor. In addition, as the polymer/crosslinker ratio increases, the recovery factor decreases, while as the polymer hydrolysis increases, the recovery factor and residual resistance factor increases.},
     year = {2019}
    }
    

    Copy | Download

  • TY  - JOUR
    T1  - Investigating the Propagation of the Colloidal Dispersion Gel (CDG) in Thick Heterogeneous Reservoirs Using Numerical Simulation
    AU  - Tariq Khamees
    AU  - Ralph Flori
    Y1  - 2019/03/16
    PY  - 2019
    N1  - https://doi.org/10.11648/j.ajset.20190401.11
    DO  - 10.11648/j.ajset.20190401.11
    T2  - American Journal of Science, Engineering and Technology
    JF  - American Journal of Science, Engineering and Technology
    JO  - American Journal of Science, Engineering and Technology
    SP  - 1
    EP  - 17
    PB  - Science Publishing Group
    SN  - 2578-8353
    UR  - https://doi.org/10.11648/j.ajset.20190401.11
    AB  - Over the last few decades, there has been a dispute regarding the ability of colloidal dispersion gels (CDG) to improve sweep efficiency more than polymer flooding. In this study, a numerical model was built using the CMG-STARS simulator to investigate the behavior of injecting 0.1 PV of CDG slug into one quarter of inverted nine-spot pattern. This slug was composed of 0.1 wt. % HPAM polymer solution with a polymer-to-crosslinker ratio (P/X) of 50/1. The model was represented by a thick heterogeneous reservoir with high water cut caused by high heterogeneity and adverse mobility ratio. Different experimental results from published literatures have been implemented in the numerical model to study the effect of these parameters on the propagation of the CDG. The results confirmed that CDG could propagate deep into the thief zones and reduce their permeability more than polymer solution. Moreover, the results showed that the shear-thinning behavior of CDG could assist the selective penetration into the high-permeability streaks only, thus reducing the cost of isolating the thief zones by mechanical methods. In addition, the results showed that the wettability had tremendous effects on the treatment. Therefore, the water-wet system yielded higher results with less damage to the low-permeability layers compared to the oil-wet system. The results showed an overestimation of the performance of post-treatment water when considering irreversible adsorption of CDG. However, the prolonged injection of post-treatment water would not remove the permeability reduction caused by CDG flooding, even with reversible adsorption. The results revealed that the higher the degradation of the CDG, the lower the recovery factor. The results showed the importance of considering a combination injection of polymer and CDG. The results also revealed that the higher the salinity of the reservoir brine and/or the makeup water, the lower the recovery factor. In addition, as the polymer/crosslinker ratio increases, the recovery factor decreases, while as the polymer hydrolysis increases, the recovery factor and residual resistance factor increases.
    VL  - 4
    IS  - 1
    ER  - 

    Copy | Download

Author Information
  • Department of Geosciences, Geological, and Petroleum Engineering, Missouri University of Science and Technology, Rolla, United States

  • Department of Geosciences, Geological, and Petroleum Engineering, Missouri University of Science and Technology, Rolla, United States

  • Sections