International Journal of Mechanical Engineering and Applications

Submit a Manuscript

Publishing with us to make your research visible to the widest possible audience.

Propose a Special Issue

Building a community of authors and readers to discuss the latest research and develop new ideas.

Welding Studies and Characterisation of Additively Manufactured LPBF Maraging Steel

Additive manufacturing (AM) comes under the category of advanced manufacturing techniques that enables the manufacture of complex shaped components with reduction in multi-part assemblies, production lead times and weight. Maraging steel is a strategic material for manufacturing of components such as rocket motor casings, bulkheads etc. in defence and aerospace sectors. Laser Powder Bed Fusion (LPBF) AM technique has been explored in fabrication of Maraging steel components for end-use applications. In many applications, additively manufactured maraging steel parts are required to be welded to conventional material and it is important to understand weldability of these materials and their characteristics to ensure good bonding between the parts. It is also necessary to assess how welding process may affect the microstructure and consequently the mechanical properties of the AM maraging steel. In the present study, welding of AM maraging steel AM300 with conventional MDN250 was explored. With the available optimized parameters, maraging steel plates (160x100x6mm3) were additively manufactured at low porosity without any defects of soot and spatter. The effect of heat treatment conditions on the volume fraction of reverted austenite in AM300 was also studied to arrive at an appropriate condition before carrying out the welding of AM300 plates. XRD and EBSD analysis revealed the formation of very fine reverted austenite in the as-deposited (AD) and Direct-aged (DA) conditions at the cell boundaries. Specimens when subjected to solution-treated and aged (STA) condition had almost eliminated the formation of reverted austenite at room temperature. Thus, the AM processed plates were subjected to solution treatment before carrying out the TIG welding of AM300 to MDN250 plates using W2 filler. Weldments of AM300-W2-MDN250 showed the formation of Fusion zone (FZ) and dark band Heat affected Zones (HAZ) on both the sides of FZ. Weld specimens subjected to ageing times at 490°C for 3.5hrs and 6hrs have shown similar average hardness values in AM300, FZ and MDN250 as 700HV, 675HV and 650HV respectively. Tensile strength and %El of as-welded, aged (3.5hrs) and aged (6hrs) specimens were evaluated to be 925MPa, 2.7%; 1730MPa, 2.4%; 1850MPa, 1.4% respectively. The tensile strength of AM300-W2-MDN250 weldment aged to 3.5hrs is found to be higher than that of conventional MDN250 weldment, but with about 60% reduction in ductility. However, higher weld strength being the main criteria, the joining of AM300 to MDN250 can be considered as a viable option for relevant applications.

Additive Manufacturing, Laser Powder Bed Fusion, Maraging Steel, TIG Welding, Microstructural Characterization, Porosity

APA Style

Ramesh Kumar Saride, Srinivas Vajjala, Brijesh Patel, Suraj Kumar, Rajesh Kumar, et al. (2023). Welding Studies and Characterisation of Additively Manufactured LPBF Maraging Steel. International Journal of Mechanical Engineering and Applications, 11(5), 100-112. https://doi.org/10.11648/j.ijmea.20231105.11

ACS Style

Ramesh Kumar Saride; Srinivas Vajjala; Brijesh Patel; Suraj Kumar; Rajesh Kumar, et al. Welding Studies and Characterisation of Additively Manufactured LPBF Maraging Steel. Int. J. Mech. Eng. Appl. 2023, 11(5), 100-112. doi: 10.11648/j.ijmea.20231105.11

AMA Style

Ramesh Kumar Saride, Srinivas Vajjala, Brijesh Patel, Suraj Kumar, Rajesh Kumar, et al. Welding Studies and Characterisation of Additively Manufactured LPBF Maraging Steel. Int J Mech Eng Appl. 2023;11(5):100-112. doi: 10.11648/j.ijmea.20231105.11

Copyright © 2023 Authors retain the copyright of this article.
This article is an open access article distributed under the Creative Commons Attribution License (http://creativecommons.org/licenses/by/4.0/) which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

1. Mercedes Pérez, Diego Carou, Eva María Rubio & Roberto Teti. (2020). “Current advances in additive manufacturing”. 13th CIRP Conference on Intelligent Computation in Manufacturing Engineering, CIRP ICME '19, Procedia CIRP 88. 439–444.
2. Brett P Conner, Guha P Manogharan, Ashley N Martof, Lauren M Rodomsky, Caitlyn M Rodomsky, Dakesha C, Jordan & James W Limperos. (2014). “Making sense of 3D printing: Creating a map of additive manufacturing products and services”, Additive Manufacturing, Vol 1-4, 64-76.
3. W. M. Garrison, May K. Banerje. (2001). “Martensitic Non-stainless Steels: High Strength and High Alloy”. Encyclopedia of Materials: Science and Technology, P5197-5202, doi.org/10.1016/B978-0-12-803581-8.02519-4.
4. Daniela Passarelo Moura da Fonsecaa Ana Larissa Melo Feitosaa Leandro Gomes de Carvalhob*, Ronald Lesley Plauta Angelo Fernando Padilha. (2021). “A Short Review on Ultra-High-Strength Maraging Steels and Future Perspectives. Materials Research”. 24 (1): e20200470, doi.org/10.1590/1980-5373-MR-2020-0470
5. FC Campbell. (2011). “Joining – Understanding the basics”, ASM International, The Materials Information Society. ISBN 978-1-61503-825-1.
6. Sakai PR, Lima, MSF, Fanton, L, Gomes CV, Lombardo S, Silva DF, Abdalla AJ. (2015). “Comparison of Mechanical and Microstructural Characteristics in Maraging 300 Steel Welded by three different processes: LASER, PLASMA and TIG”. Procedia Engineering 114 291–297.
7. Kun Li, Jiguo Shan, Chunxu Wang, Zhiling Tian. (2016). “Effect of post-weld heat treatments on strength and toughness behavior of T-250 maraging steel welded by laser beam”. Materials Science & Engineering A 663, 157–165, www.elsevier.com/locate/msea
8. Renu N Gupta, VS Raja, MK Mukherjee, and SVS Narayana Murty. (2017). “On Improving the Quality of Gas Tungsten Arc Welded 18Ni 250 Maraging Steel Rocket Motor Casings”. Metallurgical and Materials Transactions A, Volume 48A, 4655-4666.
9. P Deepak, M J Jualeash, J Jishnu, P Srinivasan, M Arivarasu, R Padmanaban and S Thirumalini. (2016). “Optimization of process parameters of pulsed TIG welded maraging steel C300”. IOP Conf. Series: Materials Science and Engineering 149, 012007 doi: 10.1088/1757-899X/149/1/012007
10. Deepak Kumar Gope, Priyanshu Kumar, Somnath Chattopadhyaya, Gowrishankar Wuriti, Tessy Thomas. (2021). “An investigation into microstructure and mechanical properties of maraging steel weldment”. IOP Conference Series: Materials Science and Engineering 1104, 012014, doi: 10.1088/1757-899X/1104/1/012014.
11. Kun Li, Jiguo Shan, Chunxu Wang, Zhiling Tian. (2016). “Influence of aging temperature on strength and toughness of laser-welded T-250 maraging steel joint”. Materials Science & Engineering A 669, 58–65.
12. Rajkumar. V, Arivazhagan. N, Devendranath Ramkumar. K. (2014). “Studies on welding of maraging steels”. MRS Singapore-ICMAT Symposia Proceedings 7th International conf. on materials for advanced technology, Procedia Engineering 75, 83-87.
13. C. R. Shamantha, R. Narayanan, K. J. L. Iyer, V. M. Radhakrishnan, S. K. Seshadri, S. Sundararajan & S. Sundaresan. (2000). “Tensile properties and fracture toughness of18Ni (250 grade) maraging steel weldments”. Science and Technology of Welding and Joining, 5: 5, 329-337, doi: 10.1179/136217100101538399.
14. Viswanathan, U. K., Dey, G. K., and Asundi, M. K. (1993). “Precipitation Hardening in 350 Grade Maraging Steel”. Metallurgical and Materials Transactions A, 24 (11), 2429–2442.
15. Rohit, B., and Muktinutalapati, N. R. (2018).“Austenite reversion in 18% Ni maraging steel and its weldments”. Materials Science and Technology, 34 (3), 253–260.
16. Schnitzer, R., Radis, R., Nöhrer, M., Schober, M., Hochfellner, R., Zinner, S., Povoden-Karadeniz, E., Kozeschnik, E., and Leitner, H. (2010). “Reverted austenite in PH 13-8 Mo maraging steels”. Materials Chemistry and Physics, 122 (1), 138–145.
17. D. Ahmadkhaniha, H. Moller, & C. Zanella. (2021). “Studying the Microstructural Effect of Selective Laser Melting and Electropolishing on the Performance of Maraging Steel”. Journal of Materials Engineering and Performance. Volume 30 (9), 6588-6605.