American Journal of Chemical Engineering

Submit a Manuscript

Publishing with us to make your research visible to the widest possible audience.

Propose a Special Issue

Building a community of authors and readers to discuss the latest research and develop new ideas.

Recycling of Used Engine Oil Using Extraction by Single Solvent

The need for virgin base oil is reduced and other resources are conserved during the refining of used, spent, or waste oils to make new lubricating oil. It is important to collect and recycle spent lubricating oil in order to protect the environment and natural resources. Although the lubricating oil itself remains unchanged after use, it becomes contaminated with combustion byproducts, deteriorated additives, water, and various dust particles during its time in the engine. The purpose of re-cycling is to eliminate degraded additives and impurities while restoring the oil's qualities to those specified by the Society of Automotive Engineers. Therefore, this study focuses on the extraction of engine oils utilizing a single solvent approach for re-cycling. The N-methyl-2-pyrrolidone was used as the solvent. The used oil was gathered from vehicle repair stations. After being allowed for settling to removing large suspended particles, the oil was subjected to a sequence of physical treatment processes. The solvent recovery process was carried out by using rotary evaporator equipment with a vacuum pump. The engine oil obtained at the end of the process is a base oil ready to be used again after addition of the proper additives. Eventually, the characteristics of the recycled oil were established and evaluated against the standards set forth by the Society of Automotive Engineers. According to the study, 10 litres of lubricating oil could be produced from 25 litres of used oil when it was recycled properly, as opposed to 220 litres of crude oil, which would be needed to make the same amount of oil.

Used, Spent or Waste Oils, Virgin Base, Lubricating Oil, Dehydration, Atmospheric Distillation, Vacuum Distillation, Solvent Extraction, Additives

APA Style

Mohamed Jurny, Mohamed Elbourawi, Ezeddine Zorgani. (2023). Recycling of Used Engine Oil Using Extraction by Single Solvent. American Journal of Chemical Engineering, 11(2), 33-38. https://doi.org/10.11648/j.ajche.20231102.11

ACS Style

Mohamed Jurny; Mohamed Elbourawi; Ezeddine Zorgani. Recycling of Used Engine Oil Using Extraction by Single Solvent. Am. J. Chem. Eng. 2023, 11(2), 33-38. doi: 10.11648/j.ajche.20231102.11

AMA Style

Mohamed Jurny, Mohamed Elbourawi, Ezeddine Zorgani. Recycling of Used Engine Oil Using Extraction by Single Solvent. Am J Chem Eng. 2023;11(2):33-38. doi: 10.11648/j.ajche.20231102.11

Copyright © 2023 Authors retain the copyright of this article.
This article is an open access article distributed under the Creative Commons Attribution License (http://creativecommons.org/licenses/by/4.0/) which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

1. Y. L. Hsu, C. H. Lee, V. B. Kreng. “Analysis and Comparison of Regenerative Technologies of Waste,” Transactions on Environment and Development, Vol. 5 (3), pp. 295 – 309, 2011.
2. L. Andrews. “Compendium of Recycling and Destruction Techno- logies for Waste Oils,” United Nations Environment Programme, 2008.
3. Silvio R. Teixeira and Gleyson T. De A. Santos, Incorporation of Waste From Used Lube Oil Re-Refining Industry In Ceramic Body: Characterization And Properties, Revista Ciências Exatas – Universidade De Taubaté (Unitau) – Brasil, 2 (1), (2008).
4. Whisman, M. L.; Reynolds, J. W.; Goetzinger, J. W.; Cotton, F. O.; Brinkman, D. W. Re-refining makes quality oils. Hydrocarb. Process. 1978, 57, page 141–145.
5. Hopmans, J. J. The Problem of the Processing of Spent Oil in the Member States of EEC; Report for the European Economic Community (EEC); National Institute for Wastewater Treatment: Dordrecht, The Netherlands, 1974.
6. Kajdas, C. Major pathways for used oil disposal and recycling, Part 1. Tribotest J. 2000, 7, page 61–74.
7. IARC (International Agency for Research on Cancer). Polynuclear Aromatic Hydrocarbons, Part 2, Carbon Blacks, Mineral Oils (Lubricant Base Oils and Derived Products) and Some Nitroarenes. In IARC Monographs on the Evaluation of Carcinogenic Risks to Humans; IARC: Lyon, France, 1984.
8. Danane et al. "Experimental regeneration process of used motor oils" Revue des Energies Renouvelables Vol. 17 N°2 (2014) 345-351.
9. Shri et al. "Studies on Reuse of Re-Refined Used Automotive Lubricating Oil" Research Journal of Engineering Sciences, (2014), Vol. 3 (6), 8-14.
10. Ihsan et al, "Recycling of Waste Engine Oils Using a New Washing Agent", Energies 2013, 6, 1023-1049; doi: 10.3390/en6021023.
11. Brownwell. (1972), “Butanol as Precipitating &Extracting Agent”, U.S. Patent: 3,639,229.
12. Rincon, J.; Canizares, P.; and Maria, T. G. (2005), “Regeneration of Used Lubricant Oil by Ethane Extraction”, Journal of Supercritical Fluids, Vol. 39, pp. 7854- 7859.
13. Nimir, O. M.; Abdul Mutalib, M. I.; and Adnan, R. (1997), “ Recycling of Used Lubrication Oil by Solvent Extraction- A Guide for Single Solvent Design”, Institute of Technology PETRONAS, 31750 Tronoh, Perak, Malaysia.
14. Manzoor, A. K.: Mahmoud, M.; and Aban. (1996), “Characteristics of Lubricating Oils, Their Environmental Impact and Survey of Disposal Methods”, Environmental Management and Health, Vol. 7, Issue 1, pp. 23-32.
15. Khelifi, O.; Giovanna, F. D.; Vranes, S.; Lodolo, A.; and Miertus, S. (2006), “Decision Support Tool for Oil Re-Generation Technologies Assessment and Selection”, Journal of Hazardous Materials, Vol. B 137, pp. 437-442.