| Peer-Reviewed

Effect of Water and Aerosols Absorption on Laser Beam Propagation in Moist Atmosphere at Eye-Safe Wavelength of 1.57 μm

Received: 4 January 2023     Accepted: 25 January 2023     Published: 6 February 2023
Views:       Downloads:
Abstract

To realize optical wireless power transmission, atmospheric propagation of eye-safe wavelength (1.57μm) laser beams was theoretically investigated. Laser beams are affected by the presence of water vapor and aerosols which absorb and scatter the laser energy. The scattering coefficients of water molecules and aerosols were estimated to be about 6.3 × 10-7 and 5.6 × 10-5 m-1, respectively, at wavelength (λ0) of 1.57μm. Furthermore, the absorption coefficients of moist air at 30% relative humidity and aerosols were estimated to be about 6.16 × 10-3 and 2.52 × 10-5 m-1, respectively, at λ0 = 1.57μm. Then simulation of laser beam propagation in the moist atmosphere at λ0 = 1.57μm was performed using these coefficients. Under the condition of no wind, the beam intensity decreases rapidly with increasing the length z and the rate of decrease slows down as the beam radius (ω) increases. When zh is defined as the z where the normalized intensity is halved, the zh (= 25 m) at ω = 20 mm when input power P = 10 W is about three times longer than that (= 8 m) when P = 100 W. This result indicates that the thermal distortion of laser beams due to accumulated heat around the z axis becomes more conspicuous as the optical power increases. The effect of this thermal beam distortion can be weakened when the laser beam is subject to crosswinds. Under the condition of gentle uniform wind with wind velocity v = 5 m/s, propagation of laser beams with ω = 20 mm was studied when P = 100 W. The zh (= 105 m) when v = 5 m/s is about 13 times longer than that (= 8 m) when v = 0 m/s. Thus, under conditions of v = 5 m/s and 30% relative humidity, laser beams with P = 100 W and ω = 20 mm can propagate over 100 m without damaging the initial beam shape at λ0 = 1.57μm.

Published in Journal of Electrical and Electronic Engineering (Volume 11, Issue 1)
DOI 10.11648/j.jeee.20231101.12
Page(s) 15-22
Creative Commons

This is an Open Access article, distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution and reproduction in any medium or format, provided the original work is properly cited.

Copyright

Copyright © The Author(s), 2023. Published by Science Publishing Group

Keywords

Laser Beam Propagation, Moist Atmosphere, Aerosol, Optical Wireless Power Transmission, Eye-Safe Wavelength

References
[1] Sumi F. H., Dutta L., and Sarker F. (2018). Future with wireless power transfer technology. J. Electrical Electronic Sys, 7 (4), 1000279.
[2] Zhao M. and Miyamoto T. (2022). Optimization for compact and high output LED-based optical wireless power transmission system. Photon., 9, 14.
[3] Miyamoto T. (2018). Optical wireless power transmission using VCSELs. Proc. Soc. Photo-Opt. Instrum. Eng., 10682, 1068204.
[4] Hirota M., Iio S., Ohta Y., Niwa Y., and Miyamoto T. (2015). Wireless power transmission between a NIR VCSEL array and silicon solar cells. 20th Microoptics Conf. (MOC'15), H86.
[5] Katsuta Y. and Miyamoto T. (2018). Design and experimental characterization of optical wireless power transmission using GaAs solar cell and series-connected high-power vertical cavity surface emitting laser array. Japn. J. Appl. Phys., 57, 08PD01-1-08DP01-7.
[6] Katsuta Y. and Miyamoto T. (2019). Design, simulation and characterization of fly-eye lens system for optical wireless power transmission. J. Appl. Phys., 58, SJJE02-1-SJJE02-8.
[7] International Electrotechnical Commission. (2007). IEC 60825 Safety of laser products-Part 1: Equipment classification and requirements. 2nd Edition.
[8] Duncan K. (2016). Laser based power transmission: component selection and laser hazard analysis. Proc. IEEE PELS Workshop on Emerging Technologies: Wireless Power Transfer (WoW), 2016, 100-103.
[9] Sahai A. and Graham D. (2011). Optical wireless power transmission at long wavelengths. Int. Conf. Space Optical Systems Applications (ICSOS 2011), 2011, 164-170.
[10] Mukherjee J., Wulfken W., Hartje H., Steinsiek F., Perren M., and Sweeney S. J. (2013). Demonstration of eye-safe (1550 nm) terrestrial laser power beaming at 30 m and subsequent conversion into electrical power using dedicated photovoltaics. 39th Photovoltaic Specialists Conf. (PVSC 2013), 1074-1076.
[11] Mukherjee J., Jarvis S., Perren M., and Sweeney S. J. (2013). Efficiency limits of laser power converters for optical power transfer applications. J. Phys. D, 46, 264006.
[12] Jarvis S., Mukherjee J., Perren M., and Sweeney S. J. (2014). Development and characterisation of laser power converters for optical power transfer applications. IET Optoelectron., 8 (2), 64-70.
[13] Minelly J. D., Barnes W. L., Laming R. I., Morkel P. R., Townsend J. E., Grubb S. G., and Payne D. N. (1993). Diode-array pumping of Er3+ / Yb3+ co-doped fiber lasers and amplifiers. IEEE Photon. Technol. Lett., 5 (3), 301-303.
[14] Vienne G. G., Caplen J. E., Dong L., Minelly J. D., Nilsson J., and Payne D. N. (1998). Fabrication and characterization of Yb3+: Er3+ phosphosilicate fibers for lasers. J. Lightwave Technol., 16 (11), 1990-2001.
[15] Cheo P. K. and King G. G. (2001). Clad-pumped Yb: Er codoped fiber lasers. IEEE Photon. Technol. Lett., 13 (3), 188-190.
[16] Nilsson J., Alam S.-U., Alvarez-Chavez J. A., Turner P. W., Clarkson W. A., and Grudinin A. B. (2003). High-power and tunable operation of erbium-ytterbium co-doped cladding-pumped fiber lasers. IEEE J. Quantum Electron., 39 (8), 987-994.
[17] Sahu J. K., Jeong Y., Richardson D. J., and Nilsson J. (2003). A 103 W erbium-ytterbium co-doped large-core fiber laser. Opt. Commun., 227, 159-163.
[18] Nilsson J., Clarkson W. A., Selvas R., Sahu J. K., Turner P. W., Alam S.-U., and Grudinin A. B. (2004). High-power wavelength-tunable cladding-pumped rare-earth-doped silica fiber lasers. Optical Fiber Technol., 10, 5-30.
[19] Laroche M., Jander P., Clarkson W. A., Sahu J. K., Nilsson J., and Jeong Y. (2004). High power cladding-pumped tunable Er, Yb-doped fibre laser. Electron. Lett., 40 (14), 855-856.
[20] Jeong Y., Alegria C., Sahu J. K., Fu L., Ibsen M., Codemard C., Mokhtar M. R., and Nilsson J. (2004). A 43-W C-band tunable narrow-linewidth erbium-ytterbium codoped large-core fiber laser. IEEE Photon. Technol. Lett., 16 (3), 756-758.
[21] Shen D. Y., Sahu J. K., and Clarkson W. A. (2005). Highly efficient Er, Yb-doped fiber laser with 188 W free-running and > 100 W tunable output power. Opt. Express, 13 (13), 4916-4921.
[22] Laroche M., Girard S., Sahu J. K., Clarkson W. A., and Nilsson J. (2006). Accurate efficiency evaluation of energy-transfer processes in phosphosilicate Er3+-Yb3+-codoped fibers. J. Opt. Soc. Am. B, 23 (2), 195-202.
[23] Jeong Y., Yoo S., Codemard C. A., Nilsson J., Sahu J. K., Payne D. N., Horley R., Turner P. W., Hickey L., Harker A., Lovelady M., and Piper A. (2007). Erbium: ytterbium codoped large-core fibre laser with 297-W continuous-wave output power. IEEE J. Selected Topics Quantum Electron., 13 (3), 573-579.
[24] Barnhardt E. A. and Streete J. L. (1970). A method for predicting atmospheric aerosol scattering coefficients in the infrared. Appl. Opt., 9 (6), 1337-1344.
[25] Gebhardt F. (1976). High power laser propagation. Appl. Opt., 15 (6), 1479-1493.
[26] Knestrick G. L., Cosden T. H., and Curcio J. A. (1962). Atmospheric scattering coefficients in the visible and infrared regions. J. Opt. Soc. Am., 52 (9), 1010-1016.
[27] Curcio J. A. (1961). Evaluation of atmospheric aerosol particle size distribution from scattering measurements in the visible and infrared. J. Opt. Soc. Am., 51 (5), 548-551.
[28] Yamamoto G. and Tanaka M. (1969). Determination of aerosol size distribution from spectral attenuation measurements. Appl. Opt., 8 (2), 447-453.
[29] van de Hulst H. C. (1957). Light Scattering by Small Particles. Chap. 20, John Wiley & Sons, New York.
[30] McClatchey R. A. and Selby J. E. A. (1974). Atmospheric Attenuation of Laser Radiation from 0.76 to 31.25μm (Environmental Research Paper 460). Air Force Cambridge Research Laboratories, Cambridge.
[31] Curcio J. A. and Petty C. C. (1951). The near infrared absorption spectrum of liquid water. J. Opt. Soc. Am., 41 (5), 302-304.
[32] Hale G. M. and Querry M. R. (1973). Optical constants of water in the 200-nm to 200-μm wavelength region. Appl. Opt., 12 (3), 555-563.
[33] Shuto Y. (2022). High-power laser beam propagation in slightly wet atmosphere. J. Electrical Electronic Eng., 10 (6), 215-222.
[34] Shoji M. (1995). Heat Transfer Textbook. Appendix F, University of Tokyo Press, Tokyo.
[35] Moosmüller H., Chakrabarty R. K., and Arnott W. P. (2009). Aerosol light absorption and its measurement: A review. J. Quantitative Spectroscopy Radiative Transfer, 110, 844-878.
[36] Bond T. C. and Bergstrom R. W. (2006). Light absorption by carbonaceous particles: An investigative review. Aerosol Science Technol., 40, 27-67.
[37] Schnaiter M., Horvath H., Möhler O., Naumann K.-H., Saathoff H., and Schöck O. W. (2003). UV-VIS-NIR spectral optical properties of soot and soot-containing aerosols. Aerosol Science, 34, 1421-1444.
[38] Weingartner E., Saathoff H., Schnaiter M., Streit N., Bitnar B., and Baltensperger U. (2003). Absorption of light by soot particles: determination of the absorption coefficient by means of aethalometers. Aerosol Science, 34, 1445-1463.
[39] Zhao G., Yu Y., Yian P., Li J., Guo S., and Zhao C. (2020). Evaluation and correction of the ambient particle spectral light absorption measured using a filter-based aethalometer. Aerosol Air Quality Research, 20, 1833-1841.
[40] Wu Y., Cheng T., and Zheng L. (2020). Light absorption of black carbon aerosols strongly influenced by particle morphology distribution. Environ. Research Lett., 15, 094051.
[41] Alexander D. T. L., Crozier P. A., and Anderson J. R. (2008). Brown carbon spheres in east asian outflow and their optical properties. Science, 321, 833-836.
[42] Andreae M. O. and Gelencsér A. (2006). Black carbon or brown carbon? The nature of light-absorbing carbonaceous aerosols. Atmos. Chem. Phys., 6, 3131-3148.
[43] Clarke A. D. and Charlson R. J. (1985). Radiative properties of the background aerosol: Absorption component of extinction. Science, 229, 263-265.
[44] Zender C. S., Bian H., and Newman D. (2003). Mineral dust entrainment and deposition (DEAD) model: Description and 1990s dust climatology. J. Geophys. Research, 108 (D14), 4416.
[45] Ohta S. and Okita T. (1990). A chemical characterization of atmospheric aerosol in Sapporo. Atmos. Environ., 24A (4), 815-822.
[46] Lukács H., Gelencsér A., Hammer S., Puxbaum H., Pio C., Legrand M., Kasper-Giebl A., Handler M., Limbeck A., Simpson D., and Preunkert S. (2007). Seasonal trends and possible sources of brown carbon based on 2-year aerosol measurements at six sites in Europe. J. Geophys. Research, 112, D23S18.
[47] Kadowaki S. (1979). Silicon and aluminum in urban aerosols for characterization of atmospheric soil particles in the Nagoya area. Environ. Science Technol., 13 (9), 1130-1134.
[48] Ångström A. (1929). On the atmospheric transmission of sun radiation and on dust in the air. J. Opt. Geogr. Ann., 11, 156-166.
[49] Smith D. C. (1977). High-power laser propagation: thermal blooming. Proc. IEEE, 65 (12), 1969-1714.
[50] Smith D. C. (1969). Thermal defocusing of CO2 laser radiation in gases. IEEE J. Quantum Electron., QE-5 (12), 600-607.
[51] Gebhardt F. G. and Smith D. C. (1969). Effects of wind on thermal defocusing of CO2 laser radiation. Appl. Phys. Lett., 14 (2), 52-54.
[52] Gebhardt F. G. and Smith D. C. (1971). Self-induced thermal distortion in the near field for a laser beam in a moving medium. IEEE J. Quantum Electron. QE-7 (2), 63-73.
Cite This Article
  • APA Style

    Yoshito Shuto. (2023). Effect of Water and Aerosols Absorption on Laser Beam Propagation in Moist Atmosphere at Eye-Safe Wavelength of 1.57 μm. Journal of Electrical and Electronic Engineering, 11(1), 15-22. https://doi.org/10.11648/j.jeee.20231101.12

    Copy | Download

    ACS Style

    Yoshito Shuto. Effect of Water and Aerosols Absorption on Laser Beam Propagation in Moist Atmosphere at Eye-Safe Wavelength of 1.57 μm. J. Electr. Electron. Eng. 2023, 11(1), 15-22. doi: 10.11648/j.jeee.20231101.12

    Copy | Download

    AMA Style

    Yoshito Shuto. Effect of Water and Aerosols Absorption on Laser Beam Propagation in Moist Atmosphere at Eye-Safe Wavelength of 1.57 μm. J Electr Electron Eng. 2023;11(1):15-22. doi: 10.11648/j.jeee.20231101.12

    Copy | Download

  • @article{10.11648/j.jeee.20231101.12,
      author = {Yoshito Shuto},
      title = {Effect of Water and Aerosols Absorption on Laser Beam Propagation in Moist Atmosphere at Eye-Safe Wavelength of 1.57 μm},
      journal = {Journal of Electrical and Electronic Engineering},
      volume = {11},
      number = {1},
      pages = {15-22},
      doi = {10.11648/j.jeee.20231101.12},
      url = {https://doi.org/10.11648/j.jeee.20231101.12},
      eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.jeee.20231101.12},
      abstract = {To realize optical wireless power transmission, atmospheric propagation of eye-safe wavelength (1.57μm) laser beams was theoretically investigated. Laser beams are affected by the presence of water vapor and aerosols which absorb and scatter the laser energy. The scattering coefficients of water molecules and aerosols were estimated to be about 6.3 × 10-7 and 5.6 × 10-5 m-1, respectively, at wavelength (λ0) of 1.57μm. Furthermore, the absorption coefficients of moist air at 30% relative humidity and aerosols were estimated to be about 6.16 × 10-3 and 2.52 × 10-5 m-1, respectively, at λ0 = 1.57μm. Then simulation of laser beam propagation in the moist atmosphere at λ0 = 1.57μm was performed using these coefficients. Under the condition of no wind, the beam intensity decreases rapidly with increasing the length z and the rate of decrease slows down as the beam radius (ω) increases. When zh is defined as the z where the normalized intensity is halved, the zh (= 25 m) at ω = 20 mm when input power P = 10 W is about three times longer than that (= 8 m) when P = 100 W. This result indicates that the thermal distortion of laser beams due to accumulated heat around the z axis becomes more conspicuous as the optical power increases. The effect of this thermal beam distortion can be weakened when the laser beam is subject to crosswinds. Under the condition of gentle uniform wind with wind velocity v = 5 m/s, propagation of laser beams with ω = 20 mm was studied when P = 100 W. The zh (= 105 m) when v = 5 m/s is about 13 times longer than that (= 8 m) when v = 0 m/s. Thus, under conditions of v = 5 m/s and 30% relative humidity, laser beams with P = 100 W and ω = 20 mm can propagate over 100 m without damaging the initial beam shape at λ0 = 1.57μm.},
     year = {2023}
    }
    

    Copy | Download

  • TY  - JOUR
    T1  - Effect of Water and Aerosols Absorption on Laser Beam Propagation in Moist Atmosphere at Eye-Safe Wavelength of 1.57 μm
    AU  - Yoshito Shuto
    Y1  - 2023/02/06
    PY  - 2023
    N1  - https://doi.org/10.11648/j.jeee.20231101.12
    DO  - 10.11648/j.jeee.20231101.12
    T2  - Journal of Electrical and Electronic Engineering
    JF  - Journal of Electrical and Electronic Engineering
    JO  - Journal of Electrical and Electronic Engineering
    SP  - 15
    EP  - 22
    PB  - Science Publishing Group
    SN  - 2329-1605
    UR  - https://doi.org/10.11648/j.jeee.20231101.12
    AB  - To realize optical wireless power transmission, atmospheric propagation of eye-safe wavelength (1.57μm) laser beams was theoretically investigated. Laser beams are affected by the presence of water vapor and aerosols which absorb and scatter the laser energy. The scattering coefficients of water molecules and aerosols were estimated to be about 6.3 × 10-7 and 5.6 × 10-5 m-1, respectively, at wavelength (λ0) of 1.57μm. Furthermore, the absorption coefficients of moist air at 30% relative humidity and aerosols were estimated to be about 6.16 × 10-3 and 2.52 × 10-5 m-1, respectively, at λ0 = 1.57μm. Then simulation of laser beam propagation in the moist atmosphere at λ0 = 1.57μm was performed using these coefficients. Under the condition of no wind, the beam intensity decreases rapidly with increasing the length z and the rate of decrease slows down as the beam radius (ω) increases. When zh is defined as the z where the normalized intensity is halved, the zh (= 25 m) at ω = 20 mm when input power P = 10 W is about three times longer than that (= 8 m) when P = 100 W. This result indicates that the thermal distortion of laser beams due to accumulated heat around the z axis becomes more conspicuous as the optical power increases. The effect of this thermal beam distortion can be weakened when the laser beam is subject to crosswinds. Under the condition of gentle uniform wind with wind velocity v = 5 m/s, propagation of laser beams with ω = 20 mm was studied when P = 100 W. The zh (= 105 m) when v = 5 m/s is about 13 times longer than that (= 8 m) when v = 0 m/s. Thus, under conditions of v = 5 m/s and 30% relative humidity, laser beams with P = 100 W and ω = 20 mm can propagate over 100 m without damaging the initial beam shape at λ0 = 1.57μm.
    VL  - 11
    IS  - 1
    ER  - 

    Copy | Download

Author Information
  • Ofra Project, Iruma City, Japan

  • Sections