| Peer-Reviewed

WASPA Neutrosophic Environment Applied to Optimization of Parameters in Milling Thin-Walled Parts

Received: 7 July 2022     Accepted: 4 August 2022     Published: 14 September 2022
Views:       Downloads:
Abstract

Traditionally, the planning of tasks that condition the manufacturing of parts in machine shops is done by experts. This condition causes inconsistencies in the information for both the planning and the manufacturing of the final product. In order to solve this problem in the following work, a solution based on the combination of the Weighted Aggregated Sum Product Assessment (WASPAS) and neutrosophy multicriteria method is used. The parameters surface roughness in the feed direction (RaFd), surface roughness in the transverse direction RaTd, and Deformation of thin aluminum parts are established in this model. The case study to perform the test, the conditions of the input values: S = 15000 rpm, doc = 0.10 mm, ts = 3.0 mm, F = 3600 m/min and the blank of thin-structured aluminum alloy material. By applying the waspas-neutrosophy strategy, it was possible to determine the best alternative with the optimum parameters to obtain a final product with the economic and competitive requirements required for the completion of the part according to the planned design process.

Published in American Journal of Mechanical and Materials Engineering (Volume 6, Issue 3)
DOI 10.11648/j.ajmme.20220603.11
Page(s) 27-33
Creative Commons

This is an Open Access article, distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution and reproduction in any medium or format, provided the original work is properly cited.

Copyright

Copyright © The Author(s), 2022. Published by Science Publishing Group

Keywords

Milling, Thin Walled, Multi-criteria Optimization, WASPAS, Neutrosophy, HSM

References
[1] G. F. Can, "An intutionistic approach based on failure mode and effect analysis for prioritizing corrective and preventive strategies," Human Factors and Ergonomics in Manufacturing & Service Industries, vol. 28, pp. 130-147, 2018.
[2] F. Ecer, D. Pamucar, S. H. Zolfani, and M. K. Eshkalag, "Sustainability assessment of OPEC countries: Application of a multiple attribute decision making tool," Journal of Cleaner Production, vol. 241, p. 118324, 2019.
[3] M. Keshavarz-Ghorabaee, K. Govindan, M. Amiri, E. K. Zavadskas, and J. Antuchevičienė, "An integrated type-2 fuzzy decision model based on WASPAS and SECA for evaluation of sustainable manufacturing strategies," Journal of Environmental Engineering and Landscape Management, vol. 27, pp. 187-200, 2019.
[4] A. R. Mishra, P. Rani, K. R. Pardasani, and A. Mardani, "A novel hesitant fuzzy WASPAS method for assessment of green supplier problem based on exponential information measures," Journal of Cleaner Production, vol. 238, p. 117901, 2019.
[5] H. Prajapati, R. Kant, and R. Shankar, "Prioritizing the solutions of reverse logistics implementation to mitigate its barriers: A hybrid modified SWARA and WASPAS approach," Journal of Cleaner Production, vol. 240, p. 118219, 2019.
[6] M. A. Sofuoğlu, "Fuzzy Applications of FUCOM Method in Manufacturing Environment," Journal of Polytechnic, 2019.
[7] C. Zhang, Q. Wang, S. Zeng, T. Baležentis, D. Štreimikienė, I. Ališauskaitė-Šeškienė, et al., "Probabilistic multi-criteria assessment of renewable micro-generation technologies in households," Journal of Cleaner Production, vol. 212, pp. 582-592, 2019.
[8] C. Kul, L. Zhang, and Y. A. Solangi, "Assessing the renewable energy investment risk factors for sustainable development in Turkey," Journal of Cleaner Production, vol. 276, p. 124164, 2020.
[9] D. Pamučar, M. Behzad, D. Božanić, and M. Behzad, "Decision making to support sustainable energy policies corresponding to agriculture sector: Case study in Iran’s Caspian Sea coastline," Journal of Cleaner Production, vol. 292, p. 125302, 2021.
[10] E. Boltürk and F. Kutlu Gündoğdu, "Prioritizing Manufacturing Challenges of a Contract Manufacturing Company for Personal Auto by Using Spherical WASPAS Method," in Decision Making with Spherical Fuzzy Sets, ed, 2021, pp. 259-275.
[11] Q. Li, Y. Ma, and S. Zhu, "Single valued Neutrosophic clustering algorithm Based on Tsallis Entropy Maximization," MDPI, 2018.
[12] F. Samarandache, "Introduction to Neutrosophic Statistics," Sitech & Education Publishing 2014.
[13] F. Smarandache, "A Unifying Field in Logics: Neutrosophic Logic. Neutrosophy, Neutrosophic Set, Neutrosophic Probability: Neutrsophic Logic. Neutrosophy, Neutrosophic Set, Neutrosophic Probability: Infinite Study.," 2005.
[14] M. Leyva Vázquez and F. Smarandache, "Neutrosofía: Nuevos avances en el tratamiento de la incertidumbre," Pons, Bruselas., 2018.
[15] J. L. a. F. S. Salmerona, "Redesigning Decision Matrix Method with an indeterminacy-based inference process. Multispace and Multistructure.," Neutrosophic Transdisciplinarity (100 Collected Papers of Sciences), vol. 4, p. 151, 2010.
[16] M. Ali, Shabir, M., Smarandache, F., and Vladareanu, L., "Neutrosophic LA-semigroup Rings," Neutrosophic Sets and Systems, vol. 7, pp. 81-88, 2015.
[17] W. V. Kandasamy and F. Smarandache, "Fuzzy Neutrosophic Models for Social Scientists". Education Publisher Inc., (2013).
[18] W. B. V. a. F. S. Kandasamy, "Fuzzy cognitive maps and neutrosophic cognitive maps.," American Research Press., 2003.
[19] R. Şahin and M. Yiğider, "A Multi-criteria neutrosophic group decision making metod based TOPSIS for supplier selection," arXiv preprint arXiv: 1412.5077., 2014.
[20] M. Leyva-Vázquez, M. A. Quiroz-Martínez, Y. Portilla-Castell, J. R. Hechavarría-Hernández, and E. González-Caballero, "A New Model for the Selection of Information Technology Project in a Neutrosophic Environment," Neutrosophic Sets Syst., p. 344.
[21] E. K. Zavadskas, M. H. Aghdaie, and S. H. Zolfani, "Decision making in machine tool selection: An integrated approach with SWARA and COPRAS-G methods," Engineering Economics, vol. 24, pp. 5-17, 2013.
[22] M. MadiĆ, J. Antucheviciene, M. RadovanoviĆ, and D. PetkoviĆ, "Determination of Manufacturing Process Conditions by Using MCDM Methods: Application in Laser Cutting," Engineering Economics, vol. 27, pp. 144-150, 2016.
[23] P. P. Das and S. Chakraborty, "Application of grey correlation-based EDAS method for parametric optimization of non-traditional machining processes," Scientia Iranica, vol. 0, pp. 0-0, 2020.
[24] M. Yazdani, E. K. Zavadskas, J. Ignatius, and M. D. Abad, "Sensitivity Analysis in MADM Methods: Application of Material Selection," Engineering Economics, vol. 27, pp. 382-391, 2016.
[25] R. P. R. Hiovanis Castillo Pantoja. Ángel Infante Haynes, Ricardo Ávila Rondón, "Application of Fuzzy-AHP and COPRAS in the selection of the best alternative for high-speed machining of thin structures in aluminum alloys Al 5083," rte, vol. 33, p. 12, 2021.
Cite This Article
  • APA Style

    Hiovanis Castillo Pantoja, Ángel Eugenio Infante Haynes. (2022). WASPA Neutrosophic Environment Applied to Optimization of Parameters in Milling Thin-Walled Parts. American Journal of Mechanical and Materials Engineering, 6(3), 27-33. https://doi.org/10.11648/j.ajmme.20220603.11

    Copy | Download

    ACS Style

    Hiovanis Castillo Pantoja; Ángel Eugenio Infante Haynes. WASPA Neutrosophic Environment Applied to Optimization of Parameters in Milling Thin-Walled Parts. Am. J. Mech. Mater. Eng. 2022, 6(3), 27-33. doi: 10.11648/j.ajmme.20220603.11

    Copy | Download

    AMA Style

    Hiovanis Castillo Pantoja, Ángel Eugenio Infante Haynes. WASPA Neutrosophic Environment Applied to Optimization of Parameters in Milling Thin-Walled Parts. Am J Mech Mater Eng. 2022;6(3):27-33. doi: 10.11648/j.ajmme.20220603.11

    Copy | Download

  • @article{10.11648/j.ajmme.20220603.11,
      author = {Hiovanis Castillo Pantoja and Ángel Eugenio Infante Haynes},
      title = {WASPA Neutrosophic Environment Applied to Optimization of Parameters in Milling Thin-Walled Parts},
      journal = {American Journal of Mechanical and Materials Engineering},
      volume = {6},
      number = {3},
      pages = {27-33},
      doi = {10.11648/j.ajmme.20220603.11},
      url = {https://doi.org/10.11648/j.ajmme.20220603.11},
      eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.ajmme.20220603.11},
      abstract = {Traditionally, the planning of tasks that condition the manufacturing of parts in machine shops is done by experts. This condition causes inconsistencies in the information for both the planning and the manufacturing of the final product. In order to solve this problem in the following work, a solution based on the combination of the Weighted Aggregated Sum Product Assessment (WASPAS) and neutrosophy multicriteria method is used. The parameters surface roughness in the feed direction (RaFd), surface roughness in the transverse direction RaTd, and Deformation of thin aluminum parts are established in this model. The case study to perform the test, the conditions of the input values: S = 15000 rpm, doc = 0.10 mm, ts = 3.0 mm, F = 3600 m/min and the blank of thin-structured aluminum alloy material. By applying the waspas-neutrosophy strategy, it was possible to determine the best alternative with the optimum parameters to obtain a final product with the economic and competitive requirements required for the completion of the part according to the planned design process.},
     year = {2022}
    }
    

    Copy | Download

  • TY  - JOUR
    T1  - WASPA Neutrosophic Environment Applied to Optimization of Parameters in Milling Thin-Walled Parts
    AU  - Hiovanis Castillo Pantoja
    AU  - Ángel Eugenio Infante Haynes
    Y1  - 2022/09/14
    PY  - 2022
    N1  - https://doi.org/10.11648/j.ajmme.20220603.11
    DO  - 10.11648/j.ajmme.20220603.11
    T2  - American Journal of Mechanical and Materials Engineering
    JF  - American Journal of Mechanical and Materials Engineering
    JO  - American Journal of Mechanical and Materials Engineering
    SP  - 27
    EP  - 33
    PB  - Science Publishing Group
    SN  - 2639-9652
    UR  - https://doi.org/10.11648/j.ajmme.20220603.11
    AB  - Traditionally, the planning of tasks that condition the manufacturing of parts in machine shops is done by experts. This condition causes inconsistencies in the information for both the planning and the manufacturing of the final product. In order to solve this problem in the following work, a solution based on the combination of the Weighted Aggregated Sum Product Assessment (WASPAS) and neutrosophy multicriteria method is used. The parameters surface roughness in the feed direction (RaFd), surface roughness in the transverse direction RaTd, and Deformation of thin aluminum parts are established in this model. The case study to perform the test, the conditions of the input values: S = 15000 rpm, doc = 0.10 mm, ts = 3.0 mm, F = 3600 m/min and the blank of thin-structured aluminum alloy material. By applying the waspas-neutrosophy strategy, it was possible to determine the best alternative with the optimum parameters to obtain a final product with the economic and competitive requirements required for the completion of the part according to the planned design process.
    VL  - 6
    IS  - 3
    ER  - 

    Copy | Download

Author Information
  • Faculty of Engineering, University of Holguin, Holguin, Cuba

  • Sections