| Peer-Reviewed

Discussion on Detection Method of Continuous Compaction Control Technology in Filling Engineering

Received: 8 September 2019     Published: 23 October 2019
Views:       Downloads:
Abstract

Compared with the traditional sampling quality detection method, the continuous compaction control technology has significant advantages in real time, full range and comprehensiveness. Therefore, this technology has gradually been widely used in the filling project. However, there are more than ten kinds of continuous compaction control methods, and the applicability of each method is different. Therefore, in order to promote the continuous application of continuous compaction control technology in China. The basic principles of various testing methods for continuous compaction control technology of filling engineering are summarized. The existing continuous compaction control technology testing methods are divided into four categories: (1) compaction method; (2) stiffness/modulus Method; (3) kinetic method; (4) energy method. The calculation process and supporting equipment of each detection method are introduced respectively. The applicability of various methods is analyzed based on the basic theory of various methods. The applicable scope and application suggestions of each detection method are proposed. The results show that the compaction method and energy method can be applied to fine-grained fillers, and the stiffness/modulus method and kinetic method can be applied to coarse-grained fillers and asphalt mixtures. According to the specific engineering conditions, the selection of suitable testing methods for continuous compaction control can obtain satisfactory application results.

Published in American Journal of Civil Engineering (Volume 7, Issue 4)
DOI 10.11648/j.ajce.20190704.15
Page(s) 113-120
Creative Commons

This is an Open Access article, distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution and reproduction in any medium or format, provided the original work is properly cited.

Copyright

Copyright © The Author(s), 2019. Published by Science Publishing Group

Keywords

Continuous Compaction Control, Detection Method, Applicability, Compaction Method

References
[1] Xu Guanghui. Dynamic principle and engineering application of continuous compaction control of roadbed [M], Beijing: Science Press, 2016.
[2] Tian Limin. Discussion on Compaction Standard and Acceptance Standard of Railway Subgrade of Passenger Dedicated Line [J]. Railway Standard Design, 2007 (11), pp. 1-4.
[3] Zhang Jialing, Xu Guanghui, Cai Ying. Study on quality inspection and control of continuous compaction roadbed [J]. Rock and Soil Mechanics, 2015, 36 (04), pp. 1141- 1146.
[4] Minnesota Department of Transportation. Mn/DOT Specification 2106 Pilot Specification for Embankment Grading Materials [S]. St Paul: Minnesota Department of Transportation Office of Research Services, 2007.
[5] Michael A. Mooney, Robert V. Rinehart, Norman W. Facas, et al. “Intelligent Soil Compaction Systems.” National Cooperative Highway Research Program Report 676 [R]. Washington, D. C.: Transportation Research Board, 2010.
[6] Fan Juan, Song Xiaodong, Tian Lifeng, Nie Zhihong. Analysis of influencing factors of continuous compaction quality inspection index CMV for high-speed railway subgrade [J]. Journal of Railway Science and Engineering, 2015, 12 (03), pp. 463-467.
[7] Anderegg, R., K. Kaufmann. “Intelligent Compaction with Vibratory Rollers.” Transportation Research Record 1868 [R]. Washington, D. C.: Transportation Research Board, 2004.
[8] Petersen, L. Continuous Compaction Control MnROAD Demonstration. Final report submitted to Mn/DOT, Report No. MN/RC-2005-07 [R]. St Paul: Minnesota Department of Transportation, 2005.
[9] XU Guang-hui, YAN Ze-hua. Study on the Limitation of Harmonic Ratio Index in the Method of Compaction in Continuous Compaction Control Technology [J]. Road Machinery & Construction Mechanization, 2015, 32 (08), pp. 39-42.
[10] Thumer H, Sandstrom A. Continuous compaction control, CCC [C]//European Workshop Compaction of Soils and Granular Materials, Presses Fonts et Chaussees, Paris, France. 2000, pp. 237-246.
[11] Nohse Y, Kitano M. Development of a new type of single drum vibratory roller [C]//Proc. 14th Intl. Conf. of the Intl. Soc. For Terrain-Vehicle Systems, Vicksburg, MS. 2002, pp. 1 -10.
[12] Krober W, Floss R, Wallrath W. Dynamic soil stiffness as quality criterion for soil compaction [J]. Geotechnics for roads, rail tracks, and earth structures, 2001, pp. 188-199.
[13] Zhang Jialing. Study on the uniformity of support stiffness of continuously compacted ballastless track subgrade structure [D]. Southwest Jiaotong University, 2014.
[14] China Railway Corporation. Q/CR 9210-2015 Technical Specification for Continuous Compaction Control of Railway Subgrade Filling Project [S]. Beijing: China Railway Publishing House, 2017.
[15] Ministry of Transport of the People's Republic of China. JT/T 1127-2017 Technical Conditions for Continuous Compaction Control System for Highway Subgrade Filling Project [S]. Beijing: China Communications Press, 2017.
[16] European Committee for Standardization. PD CEN/TS 17006:2016 Earthworks Continuous Compaction Con- trol [S]. London: BSI Standards Limited, 2017.
Cite This Article
  • APA Style

    Yu Qi, Jiang Huihuang, Gao Mingxian, Xiang Weiguo, Yan Xiaoxia, et al. (2019). Discussion on Detection Method of Continuous Compaction Control Technology in Filling Engineering. American Journal of Civil Engineering, 7(4), 113-120. https://doi.org/10.11648/j.ajce.20190704.15

    Copy | Download

    ACS Style

    Yu Qi; Jiang Huihuang; Gao Mingxian; Xiang Weiguo; Yan Xiaoxia, et al. Discussion on Detection Method of Continuous Compaction Control Technology in Filling Engineering. Am. J. Civ. Eng. 2019, 7(4), 113-120. doi: 10.11648/j.ajce.20190704.15

    Copy | Download

    AMA Style

    Yu Qi, Jiang Huihuang, Gao Mingxian, Xiang Weiguo, Yan Xiaoxia, et al. Discussion on Detection Method of Continuous Compaction Control Technology in Filling Engineering. Am J Civ Eng. 2019;7(4):113-120. doi: 10.11648/j.ajce.20190704.15

    Copy | Download

  • @article{10.11648/j.ajce.20190704.15,
      author = {Yu Qi and Jiang Huihuang and Gao Mingxian and Xiang Weiguo and Yan Xiaoxia and Wu Longliang},
      title = {Discussion on Detection Method of Continuous Compaction Control Technology in Filling Engineering},
      journal = {American Journal of Civil Engineering},
      volume = {7},
      number = {4},
      pages = {113-120},
      doi = {10.11648/j.ajce.20190704.15},
      url = {https://doi.org/10.11648/j.ajce.20190704.15},
      eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.ajce.20190704.15},
      abstract = {Compared with the traditional sampling quality detection method, the continuous compaction control technology has significant advantages in real time, full range and comprehensiveness. Therefore, this technology has gradually been widely used in the filling project. However, there are more than ten kinds of continuous compaction control methods, and the applicability of each method is different. Therefore, in order to promote the continuous application of continuous compaction control technology in China. The basic principles of various testing methods for continuous compaction control technology of filling engineering are summarized. The existing continuous compaction control technology testing methods are divided into four categories: (1) compaction method; (2) stiffness/modulus Method; (3) kinetic method; (4) energy method. The calculation process and supporting equipment of each detection method are introduced respectively. The applicability of various methods is analyzed based on the basic theory of various methods. The applicable scope and application suggestions of each detection method are proposed. The results show that the compaction method and energy method can be applied to fine-grained fillers, and the stiffness/modulus method and kinetic method can be applied to coarse-grained fillers and asphalt mixtures. According to the specific engineering conditions, the selection of suitable testing methods for continuous compaction control can obtain satisfactory application results.},
     year = {2019}
    }
    

    Copy | Download

  • TY  - JOUR
    T1  - Discussion on Detection Method of Continuous Compaction Control Technology in Filling Engineering
    AU  - Yu Qi
    AU  - Jiang Huihuang
    AU  - Gao Mingxian
    AU  - Xiang Weiguo
    AU  - Yan Xiaoxia
    AU  - Wu Longliang
    Y1  - 2019/10/23
    PY  - 2019
    N1  - https://doi.org/10.11648/j.ajce.20190704.15
    DO  - 10.11648/j.ajce.20190704.15
    T2  - American Journal of Civil Engineering
    JF  - American Journal of Civil Engineering
    JO  - American Journal of Civil Engineering
    SP  - 113
    EP  - 120
    PB  - Science Publishing Group
    SN  - 2330-8737
    UR  - https://doi.org/10.11648/j.ajce.20190704.15
    AB  - Compared with the traditional sampling quality detection method, the continuous compaction control technology has significant advantages in real time, full range and comprehensiveness. Therefore, this technology has gradually been widely used in the filling project. However, there are more than ten kinds of continuous compaction control methods, and the applicability of each method is different. Therefore, in order to promote the continuous application of continuous compaction control technology in China. The basic principles of various testing methods for continuous compaction control technology of filling engineering are summarized. The existing continuous compaction control technology testing methods are divided into four categories: (1) compaction method; (2) stiffness/modulus Method; (3) kinetic method; (4) energy method. The calculation process and supporting equipment of each detection method are introduced respectively. The applicability of various methods is analyzed based on the basic theory of various methods. The applicable scope and application suggestions of each detection method are proposed. The results show that the compaction method and energy method can be applied to fine-grained fillers, and the stiffness/modulus method and kinetic method can be applied to coarse-grained fillers and asphalt mixtures. According to the specific engineering conditions, the selection of suitable testing methods for continuous compaction control can obtain satisfactory application results.
    VL  - 7
    IS  - 4
    ER  - 

    Copy | Download

Author Information
  • Bureau Public Work of Shenzhen Municipality, Shenzhen, China

  • China Academy of Railway Sciences Corporation Limited, Beijing, China

  • Shenzhen Research and Design Institute, China Academy of Railway Sciences Corporation Limited, Shenzhen, China

  • China Academy of Railway Sciences Corporation Limited, Beijing, China

  • Shenzhen Research and Design Institute, China Academy of Railway Sciences Corporation Limited, Shenzhen, China

  • China Academy of Railway Sciences Corporation Limited, Beijing, China

  • Sections