| Peer-Reviewed

Effect of Chitosan Powder Prepared from Snail Shells to Remove Lead (II) Ion and Nickel (II) Ion from Aqueous Solution and Its Adsorption Isotherm Model

Received: 13 April 2016     Accepted: 17 May 2016     Published: 28 July 2016
Views:       Downloads:
Abstract

The toxic effects of heavy metals have remained a major source of concern globally because of their non-biodegradable nature which makes heavy metal pollution a serious environmental problem. The extents of removal for two heavy metals were investigated on adsorbent dose, temperature, pH, contact time and initial metals ion concentration. Maximum adsorption was obtained at pH 5 for Pb2+ ion and pH 7 for Ni2+ ion with 82.1% and 68.28%, at maximum adsorption temperature 335K and 355K for both metal ions with 87% and 80% metal removal respectively. The study shows that initial metal ion concentration and adsorbent dose on metals adsorption increases for both metal ions having a maximum adsorption dose at 99.93% and 70.58% removal at 180mins contact time for both metal ions with 99.83% and 70.37%. FTIR spectrum of raw chitosan showed the following peaks; 3263cm-1, 3109.25cm-1, 1627cm-1 and 2854cm-1 denoting –NH2/-NH asymmetric stretching,-OH stretching,-C=O stretching and –CH group showing that binding process for both metal ions onto chitosan bands at 3109.25cm-1 and 2854cm-1 in the spectrum. The spectra indicated –NH group was involved in the binding process due to substantial changes in absorption intensity of –NH stretching after adsorption and peak 1627cm-1 assigned to C=O occurred before the binding process. The two peaks in the 2800-2900 cm-1 region was observed in Pb2+ ion which disappear in the Ni2+ ion laden spectrum, the spectrum for Ni2+ ion has only one peak observed in this region while the Pb2+ ion has two and in the finger print region, 600-1000 cm-1, the spectra of Ni2+ ion and Pb2+ exhibited two and one peaks respectively. This supported the higher sorption capacity of Pb2+ ion over Ni2+ ion. The data were evaluated using Langmuir, Frieundlich and Temkin isotherms, the data complied with Frieundlich isotherm with high R2 values 0.984 and 0.971 for both metal ions while Temkin isotherm shows high R2 values 0.991 and 0.981 for both Pb2+ and Ni2+ ions respectively.

Published in American Journal of Applied Chemistry (Volume 4, Issue 4)
DOI 10.11648/j.ajac.20160404.15
Page(s) 146-156
Creative Commons

This is an Open Access article, distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution and reproduction in any medium or format, provided the original work is properly cited.

Copyright

Copyright © The Author(s), 2016. Published by Science Publishing Group

Keywords

Adsorption, pH, Chitosan, Heavy Metals, Snail Shells

References
[1] Ruchita Dixit, Wasiullah, Deepti Malaviya et al., (2015). Bioremediation of Heavy Metals from Soil and Aquatic Environment: An Overview of Principles and Criteria of Fundamental Processes. Journal of Sustainability 7, 2189-2212; www.mdpi.com/journal/sustainability.
[2] Barkat M, Chegrouche S, Mellah A, Bensmain B, Nibou D, Boufatit M., (2014). Application of
[3] Algerian Bentonite in the Removal of Cadmium (II) and Chromium (VI) from Aqueous Solutions. Journal of Surface Engineered Materials and Advanced Technology, Vol. 4, pp. 210-226.
[4] Morais S, Costa F. G, Pereira M. L., (2012). Heavy Metals and Human Health. Journal of Environmental Health -Emerging Issues and Practice, 978-953-307-854-860.
[5] Fenglian Fu, Qi Wang, (2011). Removal of heavy metal ions from wastewaters: A review, Journal of Environmental Management 92 (3): 407–418.
[6] Ahluwalia S. S, Goyal D., (2007). Microbial and plant derived biomass for removal of heavy metals from wastewater. Journal of Bioresour. Technol., 98, 2243–2257.
[7] Ashutosh Tripathi and Manju Rawat Ranjan., (2015). Heavy Metal Removal from Wastewater Using Low Cost Adsorbents. Journal of Bioremediation and Biodegradation. Volume 6: 315.
[8] Li W, Zhang L, Peng J, Li N, Zhang S. and Shenghui G.,(2008). Tobacco stems as a low cost adsorbent for the removal of Pb (II) from wastewater: Equilibrium and kinetic studies, Ind. Crop Prod., 28, 294−302.
[9] Ahmaruzzaman Md., (2008). Adsorption of phenolic compounds on low-cost adsorbents: A review, Adv. Colloid Interface Sci., 143, 48–67.
[10] Unlu N. and Ersoz M., (2006). Adsorption characteristics of heavy metal ions onto a low cost biopolymeric sorbent from aqueous solutions, J. Hazard Mate, 136, 272−280.
[11] Crini, G., (2006). Non-conventional low-cost adsorbents for dye removal: a review. Bio-resources Technol. 97 (9), 1061–1085.
[12] Sharma P, Kaur H, Sharma M, Sahore V., (2010). A review on applicability of naturally available adsorbents for the removal of hazardous dyes from aqueous waste. Environ. Monit. Assess., 183, 151–195.
[13] Cao, J, Tan Y. B, Che, Y. J, and Xin, H. P., (2010). Novel complex gel beads composed of hydrolyzed polyacrylamide and chitosan: an effective adsorbent for the removal of heavy metal from aqueous solution. Bioresource Technol., 101, 2558-2561.
[14] Futalan C. M, Kan C. C, Dalida M. L, Hsien K. J, Pascua C, and Wan M. W., (2011). Comparative and competitive adsorption of copper, lead, and nickel using chitosan immobilized on bentonite. Carbohyd. Polym., 83 (2), 528-536.
[15] Zhou L, Wang Y, Liu Z, Huang Q., (2009) (b). Characteristics of equilibrium, kinetics studies for adsorption of Hg (II), Cu (II), and Ni (II) ions by thiourea-modified magnetic chitosan microspheres. Journal of Hazard Mater. 161, 995–1002.
[16] Wan M. W, Kan C. C, Rogel B. D and Dalida M. L. P., (2010). Adsorption of copper (II) and lead (II) ions from aqueous solution on chitosan-coated sand. Carbohyd. Polym., 80 (3), 891-899.
[17] Varma, A. J, Deshpande, S. V, Kennedy J. F., (2004). Metal complexation by chitosan and its derivatives: a review. Carbohydrate Polymers, 55: 77-93.
[18] Ravi Kumar M. N. V, Muzzarelli R. A. A, Muzzarelli C, Sashiwa H. and Domb A. J., (2004). Chitosan Chemistry and pharmaceutical perspectives, Chem. Rev., 104, 6017–6084.
[19] Dutta P. K, Dutta J, Chattopadhyaya M. C, Tripathi V. S., (2004). Jouenal of Polym. Mater. 21, 321-334.
[20] Wan Ngah, Fatinathan W. S., 2010. Journal of Environmental Management, 91, 958.
[21] Sudha P. N., (2010). Chitin, chitosan and derivatives for waste water treatment. In: S.-K. Kim (Ed.), Chitn, Chitosan, Oligosaccharides and their Derivatives. 561- 585.
[22] Wan Ngah W. S, Teong L. C, Wong C. S, Hanafiah M. A. K. M., (2012). Preparation and Characterization of Chitosan–Zeolite Composites. Journal of applied polymer science Vol. 125, 2417–2425.
[23] Shanmugapriya A, Hemalatha M, Scholastica B and Augustine Arul Prasad T., (2013). Adsorption studies of lead (II) and nickel (II) ions on chitosan-G-polyacrylonitrile. Der Pharma Chemica, 5 (3): 141-155. Scholars Research Library; Available online at www.derpharmachemica.com
[24] Ngah W. S. W, Fatinathan S., (2008). Adsorption of Cu (II) ions in aqueous solution using chitosan beads, chitosan–GLA beads and chitosan–alginate beads. Chem Eng. J. 143, 62–72.
[25] Vasconcelos, H. L., Camargo, T. P., Goncalves, N. S., Neves, A., Laranjeira, M. C. M., Favere, V. T., (2008). Chitosan crosslinked with a metal complexing agent: synthesis, characterization and copper (II) ions adsorption. React. Funct. Polym. 68, 572–579.
[26] Muzzarelli, R. A. A., (2009). Genipin-crosslinked chitosan hydrogels as biomedical and pharmaceutical aids. Carbohydr. Polym. 77, 1–9.
[27] Wu F. C, Tseng R. L and Juang R. S., (2001). Enhanced abilities of highly swollen chitosan beads for colour removal and tyrosinase immobilization, J. Hazard. Mater. 81, 167–177.
[28] Wu, F. C., Tseng, R. L., Juang, R. S., (2001). Kinetic modeling of liquid-phase adsorption of reactive dyes and metal ions on chitosan. Water Res. 35, 613–618.
[29] Kim J. T, Lee D. Y, Oh T. S and Lee D. H., (2003). Characteristics of nitrile-butadiene rubber layered silicate nanocomposites with silane coupling agent, J. Appl. Polym. Sci., 89 (10), 2633–2640.
[30] Rhim J, Hong S, Park H. and Perry K. W., (2006). Preparation and characterization of chitosan-based nanocomposite films with antimicrobial activity, J. Agric. Food Chem. 54, 5814–5822.
[31] Wan Ngah, Fatinathan W. S., 2006. Colloid Surf A-Physicochem Eng Asp, 277, 214.
[32] Islam Md. M, Md. M. Shah, M. M. Rahman, Md. A. I. Molla, A. A. Shaikh and S. K. Roy, 2011. Preparation of chitosan from shrimp shell and investigation of its properties. Int. J. Basic Appl. Sci., 11 (1): 116-130.
[33] Nawar N, Ebrahim M. and Sami E., (2013). Removal of Heavy Metals Fe3+, Mn2+, Zn2+, Pb2+ and Cd2+ from Wastewater by Using Rice Straw as Low Cost Adsorbent. Academic.
[34] Przemysław Bartczak, Małgorzata Norman, Łukasz Klapiszewski, Natalia Karwan´ ska, Małgorzata Kawalec, Monika Baczyn´ ska, Marcin Wysokowski, Jakub Zdarta, Filip Ciesielczyk, Teofil Jesionowski., (2015). Removal of nickel (II) and lead (II) ions from aqueous solution using peat as a low-cost adsorbent: A kinetic and equilibrium study. Arabian Journal of Chemistry; doi: 10.1016/j.arabjc.07-18.
[35] Kumar D, Gaur JP., (2011). Metal biosorption by two cyanobacterial mats in relation to pH, biomass concentration, pretreatment and reuse. Bioresour Technol; 102: 2529-2535.
[36] Rathinam A, Maharshi B, Janardhanan SK, Jonnalagadda RR, Nair BU.,(2010). Biosorption of cadmium metal ion from simulated wastewaters using Hypnea valentiae biomass: a kinetic and thermodynamic study. Bioresour Technol; 101: 1466-1470.
[37] Asubiojo OI, Ajelabi, OB., (2009). The removal of heavy metals from aqueous solution by natural adsorbent. Journal of Environental Chemical Toxicology. 91: 883-890.
[38] Choi H. D, Cho J. M, Xang J. S, Lee J. X., (2009). Influence of cationic surfactant on adsorsoption of Cr (VI) onto activated carbon. J. Hazad. Mater. 161: 1565-1568.
[39] Dhabab JM., 2011). Removal of Fe (II), Cu (II), Zn (II), and Pb (II) ions from aqueous solutions by duckweed. J. Oceano. Marine Sci. 2 (1): 17-22.
[40] Chowdhury Z, Zain S. M and Rashid A. K., (2010). Equilibrium Isotherm Modeling, Kinetics and Thermodynamics Study for Removal of Lead from Wastewater, J. of Chem. Sci., 8 (1), 333-339.
[41] Abbas S. T, Mustafa M, Al-Faize and Rah A. Z., (2013). Adsorption of Pb2+ and Zn2+ ion from oil wells onto activated carbon produced from Rice Husk in batch adsorption process, Journal. Chem. Pharm. Res., 5 (4), 240-250.
[42] Kamari, A. and Ngah W. S. W., (2009). Isotherm, kinetic and thermodynamic studies of lead and copper uptake by H2SO4 modified chitosan. Colloid Surface. B, 73 (2), 257-266.
[43] Bhattacharya A. K, Mandal S. N, Das S. K, 2006. Adsorption of Zn (II) from aqueous solution by using Different adsorbents. Chemical Engineering Journal, 123: 43–51pp.
[44] Ozer, A. and Ozer, D. (2003). Comparative study of the biosorption of Pb (II), Ni (II) and Cr (VI) ions. Journal of Hazardous Material, 1: 219-229.
[45] Vedia Nüket Tirtom, Ayşe Dinçer, Seda Becerik, TülinAydemir and Ali Çelik., 2012). Removal of lead (II) ions from aqueous solution by using crosslinked chitosan-clay beads. Desalination and Water Treatment 39: 76–82.
[46] Mataka L, Salidu, S, Masamba W and Mwatseteza J., (2010). Cadmium sorption by Moingastenopetala and Moringa oleiferaseed powder. International Journal Environmental Science Technology, 3 131-139.
[47] Kannamba B, and Reddy K. L, Apparao B. V., (2010). Removal of Cu (II) from aqueous solutions using chemically modified chitosan.” Journal of Hazardous Materials, 175, 939-948.
[48] Abdel-Ghani N, Hefny M, El-Chaghaby G., (2007). Removal of lead from aqueous solution using low cost abundantly available adsorbents. 4: 67-73.
[49] Sugashini S, Gopalakrishnan S., (2012). Studies on the Performance of Protonated cross linked Chitosan Beads (PCCB) for Chromium Removal. Res J. Chem. Sci. 2 (6): 55-59.
[50] Xiaomin Li, Yanru Tang, Xiuju Cao, Dandan Lu, Fang Luo, enjing Shao., (2008). Preparation and evaluation of orange peel cellulose adsorbents for effective removal of cadmium, zinc, cobalt and nickel, Journal of Colloids and Surfaces A: Physicochemical and Engineering Aspect Volume 317, Issues 1–3, Pages 512–521.
[51] Ramya R, Sankar P, Anbalagan S, Sudha P. N., (2011). Adsorption of Cu (II) and Ni (II) ions from metal solution using crosslinked chitosangacrylonitrile copolymer. International journal of environmental sciences Volume 1, No 6.
[52] Reena Malik, Suman Lata et al 2015. Removal of heavy metal from waste water by the use of modified aloe vera leaf powder. International Journal of Basic and Applied Chemical Sciences. Vol. 5 (2) April-June, pp. 6-17.
[53] Santhi T and Manonmani S., (2009). Adsorption kinetics of cationic dyes from aqueous solution by Bioadsorption onto activiated in Environmental sanitation 4 (3): 263-271.
[54] Romera, E, Gonzalez F, Ballester A. and Blazquez Munoz J. A., (2007). Comparative study of heavy metals using different types of algae. Bioresource Technology, 98: 3344-335.
[55] Sheng P. X, Ting Y. P, Chen J. P. and Hong L., (2004). Sorption of lead, copper, cadmium, zinc and nickel by marine algal biomass: Characterization of biosorptive capacity and investigation of mechanisms. Journal of Colloid and Interface Science, 275: 131-141.
[56] Feng N, Guo X, Liang S, Zhu Y, Liu J., (2011) Biosorption of heavy metals from aqueous solutions by chemically modified orange peel. J Hazard Mater; 185: 49-54.
[57] Sha Liang, XueyiGuo, Ningchuanfeng, Qinghua Tian., (2010). Isotherms Kinetics and thermodynamic studies of adsorption of Cu2+ from aqueous solution by Mg2+ /K+ type orange peel adsorbents, Journal of Hazardous Materials, 174, 756-762.
[58] Lohani M. B, Singh A, Rupainwar D. C and Dhar D. N., (2008). Studies on efficiency of guava (Psidiumguajava) bark as bioadsorbent for removal Hg (II) from aqueous solutions, J. of Hazard Mater, 159, 626-629.
[59] Meena, A. K., Mishra, G. K., Kumar, S., Rajagopal, C., and Nagar, P. N. (2003). Adsorption of Ni (II) and Zn (II) from aqueous solution by chemically treated activated carbon. National Conference on Carbon, DMSRDE, Kanpur, pp 31140.
[60] Hoang V. T, Lam D. T and Thinh N. N., (2010). Preparation of chitosan / magnetite composite beads and their application for removal of Pb (II) and Ni (II) from aqueous solution, Mater. Sci. Eng. C, 30, 304–310.
[61] Laus R, Costa T. G, Szpoganicz B. and Fávere V. T., (2010). Adsorption and desorption of Cu (II), Cd (II) and Pb (II) ions using chitosan crosslinked with epichlorohydrin-triphosphate as the adsorbent, J. Hazard. Mater., 183: 233−241.
[62] Mini N. and. Bajpai S. K., (2008). Chitosan–magnetite nanocomposites (CMNs) as magnetic carrier particles for removal of Fe (III) from aqueous solutions, Colloid. Surface., 320: 161−168.
[63] Pahlavanzadeh H, Keshtkara R, Safdari J, Abadi Z., (2010). Biosorption of Nickel (II) from aqueous solution by brown algae: equilibrium, dynamic and thermodynamic studies. J Hazard Mater; 175: 304-310.
[64] Malkoc, E. and Nuhoglu Y., 2005. Investigations of Ni (II) removal from aqueous solutions using tea factory waste. Journal of Hazardous Materials, 127: 120-128.
[65] Thilagan J, Gopalakrishnan S and Kannadasan T., 2013. A comparative study on adsorption of copper (ii) ions in aq, ueous solution by; (a) chitosan blended with cellulose and cross linked by formaldehyde (b) chitosan immobilised on red soil, (c) chitosan reinforced by banana stem fibre. International Journal of Applied Engineering and Technology. An Online International Journal Available at http://www.cibtech.org/jet. Vol. 3 (1) January-March, pp. 35-36.
[66] Nour T. Abdel-Ghani and Ghadir A. El-Chaghaby., (2014). Biosorption for metal ions removal from aqueous solutions: a review of recent studies. International Journal of Latest Research in Science and Technology Volume 3, Issue 1: Page No. 24-42.
[67] Naiya TK, Bhattacharya AK, Mandal S, Das SK., (2009). The sorption of lead (II) ions on rice husk ash. Journal of Hazard Mater; 163: 1254-1264.
[68] Mittal A, Mittal J, Malviya A, Kaur D, Gupta VK., (2010.) Adsorption of hazardous dye crystal violet from wastewater by waste materials. Journal of Colloid Interface Sci 343: 463-473.
[69] Febrianto J, Kosasih A. N, Sunarso J, Ju Y. H, Indraswati N, Ismadji, S., 2009). Equilibrium and kinetic studies in adsorption of heavy metals using biosorbent: a summary of recent studies. J. Hazard. Mater. 162, 616–645.
[70] Farhan AM, Al-Dujaili AH, Awwad AM., (2013). Equilibrium and kinetic studies of cadmium (II) and lead (II) ions biosorption onto Ficus carcia leaves. International Journal of Industrial Chemistry; 24.
[71] Abdel-Ghani NT, Hegazy AK, El-Chaghaby G., (2009). Typha domingensis leaf powder for decontamination of aluminium, iron, zinc and lead: Biosorption kinetics and equilibrium modeling. 6: 243-248.
[72] Patil S, Bhole A, Natrajan G,. (2006). Scavenging of nickel (II) metal ions by adsorption on PAC and Babhul Back. Journal of environmental science and energy; 48 (3): 203-208.
[73] Kausar A, Nawaz H, Mackinnon G., (2013). Equilibrium, kinetic and thermodynamic studies on the removal of U (VI) by low cost agricultural waste. Colloids Surfaces Bio-interfaces. 111: 24-13.
Cite This Article
  • APA Style

    Olayinka John Akinyeye, Tope Babatunde Ibigbami, Oluwakayode Odeja. (2016). Effect of Chitosan Powder Prepared from Snail Shells to Remove Lead (II) Ion and Nickel (II) Ion from Aqueous Solution and Its Adsorption Isotherm Model. American Journal of Applied Chemistry, 4(4), 146-156. https://doi.org/10.11648/j.ajac.20160404.15

    Copy | Download

    ACS Style

    Olayinka John Akinyeye; Tope Babatunde Ibigbami; Oluwakayode Odeja. Effect of Chitosan Powder Prepared from Snail Shells to Remove Lead (II) Ion and Nickel (II) Ion from Aqueous Solution and Its Adsorption Isotherm Model. Am. J. Appl. Chem. 2016, 4(4), 146-156. doi: 10.11648/j.ajac.20160404.15

    Copy | Download

    AMA Style

    Olayinka John Akinyeye, Tope Babatunde Ibigbami, Oluwakayode Odeja. Effect of Chitosan Powder Prepared from Snail Shells to Remove Lead (II) Ion and Nickel (II) Ion from Aqueous Solution and Its Adsorption Isotherm Model. Am J Appl Chem. 2016;4(4):146-156. doi: 10.11648/j.ajac.20160404.15

    Copy | Download

  • @article{10.11648/j.ajac.20160404.15,
      author = {Olayinka John Akinyeye and Tope Babatunde Ibigbami and Oluwakayode Odeja},
      title = {Effect of Chitosan Powder Prepared from Snail Shells to Remove Lead (II) Ion and Nickel (II) Ion from Aqueous Solution and Its Adsorption Isotherm Model},
      journal = {American Journal of Applied Chemistry},
      volume = {4},
      number = {4},
      pages = {146-156},
      doi = {10.11648/j.ajac.20160404.15},
      url = {https://doi.org/10.11648/j.ajac.20160404.15},
      eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.ajac.20160404.15},
      abstract = {The toxic effects of heavy metals have remained a major source of concern globally because of their non-biodegradable nature which makes heavy metal pollution a serious environmental problem. The extents of removal for two heavy metals were investigated on adsorbent dose, temperature, pH, contact time and initial metals ion concentration. Maximum adsorption was obtained at pH 5 for Pb2+ ion and pH 7 for Ni2+ ion with 82.1% and 68.28%, at maximum adsorption temperature 335K and 355K for both metal ions with 87% and 80% metal removal respectively. The study shows that initial metal ion concentration and adsorbent dose on metals adsorption increases for both metal ions having a maximum adsorption dose at 99.93% and 70.58% removal at 180mins contact time for both metal ions with 99.83% and 70.37%. FTIR spectrum of raw chitosan showed the following peaks; 3263cm-1, 3109.25cm-1, 1627cm-1 and 2854cm-1 denoting –NH2/-NH asymmetric stretching,-OH stretching,-C=O stretching and –CH group showing that binding process for both metal ions onto chitosan bands at 3109.25cm-1 and 2854cm-1 in the spectrum. The spectra indicated –NH group was involved in the binding process due to substantial changes in absorption intensity of –NH stretching after adsorption and peak 1627cm-1 assigned to C=O occurred before the binding process. The two peaks in the 2800-2900 cm-1 region was observed in Pb2+ ion which disappear in the Ni2+ ion laden spectrum, the spectrum for Ni2+ ion has only one peak observed in this region while the Pb2+ ion has two and in the finger print region, 600-1000 cm-1, the spectra of Ni2+ ion and Pb2+ exhibited two and one peaks respectively. This supported the higher sorption capacity of Pb2+ ion over Ni2+ ion. The data were evaluated using Langmuir, Frieundlich and Temkin isotherms, the data complied with Frieundlich isotherm with high R2 values 0.984 and 0.971 for both metal ions while Temkin isotherm shows high R2 values 0.991 and 0.981 for both Pb2+ and Ni2+ ions respectively.},
     year = {2016}
    }
    

    Copy | Download

  • TY  - JOUR
    T1  - Effect of Chitosan Powder Prepared from Snail Shells to Remove Lead (II) Ion and Nickel (II) Ion from Aqueous Solution and Its Adsorption Isotherm Model
    AU  - Olayinka John Akinyeye
    AU  - Tope Babatunde Ibigbami
    AU  - Oluwakayode Odeja
    Y1  - 2016/07/28
    PY  - 2016
    N1  - https://doi.org/10.11648/j.ajac.20160404.15
    DO  - 10.11648/j.ajac.20160404.15
    T2  - American Journal of Applied Chemistry
    JF  - American Journal of Applied Chemistry
    JO  - American Journal of Applied Chemistry
    SP  - 146
    EP  - 156
    PB  - Science Publishing Group
    SN  - 2330-8745
    UR  - https://doi.org/10.11648/j.ajac.20160404.15
    AB  - The toxic effects of heavy metals have remained a major source of concern globally because of their non-biodegradable nature which makes heavy metal pollution a serious environmental problem. The extents of removal for two heavy metals were investigated on adsorbent dose, temperature, pH, contact time and initial metals ion concentration. Maximum adsorption was obtained at pH 5 for Pb2+ ion and pH 7 for Ni2+ ion with 82.1% and 68.28%, at maximum adsorption temperature 335K and 355K for both metal ions with 87% and 80% metal removal respectively. The study shows that initial metal ion concentration and adsorbent dose on metals adsorption increases for both metal ions having a maximum adsorption dose at 99.93% and 70.58% removal at 180mins contact time for both metal ions with 99.83% and 70.37%. FTIR spectrum of raw chitosan showed the following peaks; 3263cm-1, 3109.25cm-1, 1627cm-1 and 2854cm-1 denoting –NH2/-NH asymmetric stretching,-OH stretching,-C=O stretching and –CH group showing that binding process for both metal ions onto chitosan bands at 3109.25cm-1 and 2854cm-1 in the spectrum. The spectra indicated –NH group was involved in the binding process due to substantial changes in absorption intensity of –NH stretching after adsorption and peak 1627cm-1 assigned to C=O occurred before the binding process. The two peaks in the 2800-2900 cm-1 region was observed in Pb2+ ion which disappear in the Ni2+ ion laden spectrum, the spectrum for Ni2+ ion has only one peak observed in this region while the Pb2+ ion has two and in the finger print region, 600-1000 cm-1, the spectra of Ni2+ ion and Pb2+ exhibited two and one peaks respectively. This supported the higher sorption capacity of Pb2+ ion over Ni2+ ion. The data were evaluated using Langmuir, Frieundlich and Temkin isotherms, the data complied with Frieundlich isotherm with high R2 values 0.984 and 0.971 for both metal ions while Temkin isotherm shows high R2 values 0.991 and 0.981 for both Pb2+ and Ni2+ ions respectively.
    VL  - 4
    IS  - 4
    ER  - 

    Copy | Download

Author Information
  • Engineering Materials Research Department, Nigerian Building and Road Research Institute, Sango Ota, Ogun State, Nigeria

  • Healthy Life for All Foundation, University College Hospital Ibadan, Oyo State, Nigeria

  • Federal University of Petroleum Resources, Effurum, Delta State, Nigeria

  • Sections