Dye sensitized solar cells (DSSC) are used for photovoltaic applications. The paper presents a methodology for optical and electrical modeling of dye-sensitized solar cells (DSSCs). In order to take into account the influence of the overlap distance between two TiO2 particles on the cell an optoelectronic model for DSSC is presented in this paper. From the radiative transfer equation and Mie theory, the optical generation rate of cell is deduced. Coupling the output of the optical model (the dye absorption rate) to an electrical model allows determination of short-circuit current density and maximum power output. Due to our model, the dependence effects of the overlap distance upon the porosity, the optical generation rate, the short circuit current density and the maximum power output are evidenced. Thus, we see that when the overlap distance increases the porosity decreases. In addition, when the overlap distance increases, the absorption rate decreases when the overlap distance is greater than TiO2 radius divide by 5. Moreover, we see that when the overlap distance is lower than the TiO2 radius divided by 5, the short circuit current density and the maximum power output increase. However, when the overlap distance is higher than TiO2 radius divided by 5 they decrease. Thus, according to the model, we see that the optimal overlap distance is equal to TiO2 radius divide by 5. Our results agree with those found in the literature.
| Published in | American Journal of Modern Physics (Volume 6, Issue 1) |
| DOI | 10.11648/j.ajmp.20170601.11 |
| Page(s) | 1-9 |
| Creative Commons |
This is an Open Access article, distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution and reproduction in any medium or format, provided the original work is properly cited. |
| Copyright |
Copyright © The Author(s), 2024. Published by Science Publishing Group |
Dye-Sensitized Solar Cell, Optical Parameters, Electrical Parameters, Overlap Distance, TiO2 Radius
| [1] | O’Regan, B., Grätzel, M., ‘‘A low-cost, high-efficiency solar cell based on dye-sensitized colloidal TiO2 films,’’ Nature, 353-737, 1991. |
| [2] | Wang, Q., Ito, S., Gratzel, M., Fabregat-Santiago, F., Mora-Sero, I., Bisquert, J., Bessho, T., and Imai, H., ‘‘Characteristics of High Efficiency Dye-Sensitized Solar Cells,’’ J. Phys. Chem. B 110, 25210-25221, 2006. |
| [3] | Mathew, S., Yella, A., Gao, P., Humphry-Baker, R., Curchod, B. F. E., Tavernelli, I., Rothlisberger, U., Nazeeruddin M. K., and Grätzel, M., ‘‘Dye-sensitized solar cells with 13% efficiency achieved through the molecular engineering of porphyrin sensitizers,’’ Nature Chemistry 6, 242–247, 2014. |
| [4] | Green, M. A., Emery, K., Hishikawa, Y., Warta, W., and Dunlop, E. D., ‘‘Solar cell efficiency tables (Version 45),’’ Progress in photovoltaics: research and applications, 23 (1), 1-9, 2015. |
| [5] | Chiba, Y.; Islam, A.; Watanabe, Y.; Komiya, R.; Koide, N.; Han, L., J. Appl. Phys., Part 2, 45, L638–L640, 2006. |
| [6] | Gao, F.; Wang, Y., Shi, D., Zhang, J., Wang, M. K., Jing, X. Y., Humphry-Baker, R., Wang, P., Zakeeruddin, S. M., Grätzel, M., J. Am. Chem. Soc. 130, 10720–10728, 2008. |
| [7] | Ferber, J., and Luther, J., ‘‘Computer simulations of light scattering and absorption in dye-sensitized solar cells.’’ Solar Energy Materials and Solar Cells 54 (1998) |
| [8] | Rothenberger, G., Comte, P., Gratzel, M., ‘‘A contribution to the optical design of dye_sensitized nanocrystalline solar cells,’’ Solar Energy Materials & Solar Cells, 58, 321-336, 1999. |
| [9] | Soedergren, S., Hagfeldt, A., Olsson, J., and Lindquist, S. E., ‘‘Theoretical models for the action spectrum and the current-voltage characteristics of microporous semiconductor films in photoelectrochemical cells,’’ The Journal of Physical Chemistry, 98 (21), 5552-5556, 1994. |
| [10] | Matthews, D., Infelta, P., and Grätzel, M, ‘‘Calculation of the photocurrent-potential characteristic for regenerative, sensitized semiconductor electrodes.’’ Solar Energy Materials and Solar Cells, 44 (2), 119-155, 1996. |
| [11] | Ferber, J., Stangl, R., and Luther, J., “An electrical model of the dye-sensitized solar cell,” Solar Energy Materials and Solar Cells, 53 (1), 29-54, 1998. |
| [12] | Usami, A., “Theoretical study of application of multiple scattering of light to a dye-sensitized nanocrystalline photoelectrichemical cell,” Chemical Physics Letters, 277 (1), 105-108, 1997. |
| [13] | Usami, A., “Theoretical study of charge transportation in dye-sensitized nanocrystalline TiO2 electrodes,” Chemical physics letters, 292 (1), 223-228, 1998. |
| [14] | Ferber, J., Stangl, R., and Luther, J., “An electrical model of the dye-sensitized solar cell,” Solar Energy Materials and Solar Cells, 53 (1), 29-54, 1998. |
| [15] | Stangl, R., Ferber, J., & Luther, J., ‘‘On the modeling of the dye-sensitized solar cell,’’ Solar Energy Materials and Solar Cells, 54 (1), 255-264, 1998. |
| [16] | Usami, A., & Ozaki, H., ‘‘Computer simulations of charge transport in dye-sensitized nanocrystalline photovoltaic cells,’’ The Journal of Physical Chemistry B, 105 (20), 4577-4583, 2001. |
| [17] | Bisquert, J., Cahen, D., Hodes, G., Rühle, S., & Zaban, A., ‘‘Physical chemical principles of photovoltaic conversion with nanoparticulate, mesoporous dye-sensitized solar cells,’’ The Journal of Physical Chemistry B, 108 (24), 8106-8118, 2004. |
| [18] | Filipič, M., Berginc, M., Smole, F., & Topič, M., ‘‘Analysis of electron recombination in dye-sensitized solar cell,’’ Current Applied Physics, 12 (1), 238-246, 2012. |
| [19] | Wenger, S., Schmid, M., Rothenberger, G., Gentsch, A., Gratzel, M., and Schumacher, J. O., ‘‘Coupled Optical and Electronic Modeling of Dye-Sensitized Solar Cells for Steady-State Parameter Extraction,’’ J. Phys. Chem. C 115, 10218–10229, 2011. |
| [20] | Topič, M., Čampa, A., Filipič, M., Berginc, M., Krašovec, U. O., & Smole, F., ‘‘Optical and electrical modelling and characterization of dye-sensitized solar cells,’’ Current Applied Physics, 10 (3), S425-S430, 2010. |
| [21] | Taylor, S. W. ‘‘Transport of substrate and biomass in porous media with application to in situ bioremediation of organic contaminants in groundwater,’’ PhD thesis, Department of Civil Engineering, Princeton, 1990. |
| [22] | Taylor, N. J., Milly, S. W., and Jaffe, P. R., ‘‘Biofilm growth and the related changes in the physical properties of a porous medium, 2, Permeability,’’ Water Resour. Res., 26 (9), 2161–2169, 1990. |
| [23] | Deb, A. K. ‘‘Theory of sand filtration.’’ J. Sanit. Eng. Div., ASCE, 96 (3), 399–422. (1969). |
| [24] | B. Maheu, J. N. Letoulouzan and G. Gouesbet. Four-flux models to solve the scattering transfer equation in terms of Lorenz-Mie parameters. Applied Optics Vol. 23, No. 19 (1984). |
| [25] | G. Kortum, Reflectance Spectroscopy, Springer, Berlin, 1969. |
| [26] | C. Rozé, T. Girasole, G. Gréhan, G. Gouesbet, B. Maheu. Four-flux models to solve the scattering transfer equation in terms of Lorenz-Mie parameters. Optics communications 194 (2001) 251-263. |
| [27] | A. Dioum, S. Ndiaye, E. H. O. Gueye, M. B. Gaye, D. N. Faye, O. Sakho, M. Faye and A. C. Beye. 3-D Modeling of bilayer heterojunction organic solar cell based on Copper Phthalocyanine and Fullerene (CuPc/C60): evidence of total excitons dissociation at the donor-acceptor interface. Global Journal of Pure and Applied Sciences, Vol 19 (2013). |
| [28] | Benkstein, K. D., Kopidakis, N., van de Lagemaat, J., Frank, A. J., ‘‘Influence of the Percolation Network Geometry on Electron Transport in Dye-Sensitized Titanium Dioxide Solar Cells,’’ Phys. Chem. B, 107-114, 2003. |
| [29] | Saito, Y., Kambe, S., Kitamura, T., Wada, Y., and Yanagida, S., ‘‘Morphology control of mesoporous TiO2 nanocrystalline films for performance of dye-sensitized solar cells,’’ Solar Energy Materials and Solar Cells, 83 (1), 1-13, 2004. |
APA Style
El Hadji Oumar Gueye, Papa Douta Tall, Kharouna Talla, Abdoulaye Ndiaye Dione, Allé Dioum, et al. (2017). Optical and Electrical Modeling of Dye Sensitized Solar Cell: Influence of the Overlap Distance Between TiO2 Particles. American Journal of Modern Physics, 6(1), 1-9. https://doi.org/10.11648/j.ajmp.20170601.11
ACS Style
El Hadji Oumar Gueye; Papa Douta Tall; Kharouna Talla; Abdoulaye Ndiaye Dione; Allé Dioum, et al. Optical and Electrical Modeling of Dye Sensitized Solar Cell: Influence of the Overlap Distance Between TiO2 Particles. Am. J. Mod. Phys. 2017, 6(1), 1-9. doi: 10.11648/j.ajmp.20170601.11
AMA Style
El Hadji Oumar Gueye, Papa Douta Tall, Kharouna Talla, Abdoulaye Ndiaye Dione, Allé Dioum, et al. Optical and Electrical Modeling of Dye Sensitized Solar Cell: Influence of the Overlap Distance Between TiO2 Particles. Am J Mod Phys. 2017;6(1):1-9. doi: 10.11648/j.ajmp.20170601.11
Share This Article
Twitter
Linked In
Facebook
Copy
Download@article{10.11648/j.ajmp.20170601.11,
author = {El Hadji Oumar Gueye and Papa Douta Tall and Kharouna Talla and Abdoulaye Ndiaye Dione and Allé Dioum and Mouhamadou Bachir Gaye and Ndeye Maty Ndiaye and Balla Diop Ngom and Aboubaker Chedikh Beye},
title = {Optical and Electrical Modeling of Dye Sensitized Solar Cell: Influence of the Overlap Distance Between TiO2 Particles},
journal = {American Journal of Modern Physics},
volume = {6},
number = {1},
pages = {1-9},
doi = {10.11648/j.ajmp.20170601.11},
url = {https://doi.org/10.11648/j.ajmp.20170601.11},
eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.ajmp.20170601.11},
abstract = {Dye sensitized solar cells (DSSC) are used for photovoltaic applications. The paper presents a methodology for optical and electrical modeling of dye-sensitized solar cells (DSSCs). In order to take into account the influence of the overlap distance between two TiO2 particles on the cell an optoelectronic model for DSSC is presented in this paper. From the radiative transfer equation and Mie theory, the optical generation rate of cell is deduced. Coupling the output of the optical model (the dye absorption rate) to an electrical model allows determination of short-circuit current density and maximum power output. Due to our model, the dependence effects of the overlap distance upon the porosity, the optical generation rate, the short circuit current density and the maximum power output are evidenced. Thus, we see that when the overlap distance increases the porosity decreases. In addition, when the overlap distance increases, the absorption rate decreases when the overlap distance is greater than TiO2 radius divide by 5. Moreover, we see that when the overlap distance is lower than the TiO2 radius divided by 5, the short circuit current density and the maximum power output increase. However, when the overlap distance is higher than TiO2 radius divided by 5 they decrease. Thus, according to the model, we see that the optimal overlap distance is equal to TiO2 radius divide by 5. Our results agree with those found in the literature.},
year = {2017}
}
TY - JOUR T1 - Optical and Electrical Modeling of Dye Sensitized Solar Cell: Influence of the Overlap Distance Between TiO2 Particles AU - El Hadji Oumar Gueye AU - Papa Douta Tall AU - Kharouna Talla AU - Abdoulaye Ndiaye Dione AU - Allé Dioum AU - Mouhamadou Bachir Gaye AU - Ndeye Maty Ndiaye AU - Balla Diop Ngom AU - Aboubaker Chedikh Beye Y1 - 2017/02/03 PY - 2017 N1 - https://doi.org/10.11648/j.ajmp.20170601.11 DO - 10.11648/j.ajmp.20170601.11 T2 - American Journal of Modern Physics JF - American Journal of Modern Physics JO - American Journal of Modern Physics SP - 1 EP - 9 PB - Science Publishing Group SN - 2326-8891 UR - https://doi.org/10.11648/j.ajmp.20170601.11 AB - Dye sensitized solar cells (DSSC) are used for photovoltaic applications. The paper presents a methodology for optical and electrical modeling of dye-sensitized solar cells (DSSCs). In order to take into account the influence of the overlap distance between two TiO2 particles on the cell an optoelectronic model for DSSC is presented in this paper. From the radiative transfer equation and Mie theory, the optical generation rate of cell is deduced. Coupling the output of the optical model (the dye absorption rate) to an electrical model allows determination of short-circuit current density and maximum power output. Due to our model, the dependence effects of the overlap distance upon the porosity, the optical generation rate, the short circuit current density and the maximum power output are evidenced. Thus, we see that when the overlap distance increases the porosity decreases. In addition, when the overlap distance increases, the absorption rate decreases when the overlap distance is greater than TiO2 radius divide by 5. Moreover, we see that when the overlap distance is lower than the TiO2 radius divided by 5, the short circuit current density and the maximum power output increase. However, when the overlap distance is higher than TiO2 radius divided by 5 they decrease. Thus, according to the model, we see that the optimal overlap distance is equal to TiO2 radius divide by 5. Our results agree with those found in the literature. VL - 6 IS - 1 ER -
Information
Email: